RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 11
1
2
3
Last »
Search: Posts Made By: Jamxx
Showing results 1 to 25 of 274
Search took 0.66 seconds.
Forum: RC Nitro Stadium Trucks
07-31-2005, 11:15 PM
Replies: 3
Views: 884
Posted By Jamxx

RE: HPI Nitro Rush Promblems

Just for future reference, if your car is bogging down like that (as in it sounds like there is too much fuel for the engine and not enough air to properly burn) then your needle(s) are too rich....
Forum: RC Nitro Stadium Trucks
07-28-2005, 05:45 PM
Replies: 17
Views: 810
Posted By Jamxx

RE: getting a rush evo to wheelie?

I would just get the yellow soft springs (that's what I use on my MT2) and the stiff and stiffer springs. I think the stiffest is the purple, but I'm not sure. Then you can just experiment! I pair of...
Forum: RC Nitro Stadium Trucks
07-27-2005, 10:55 PM
Replies: 6
Views: 500
Posted By Jamxx

RE: New Pipe for a .26 HB LSP.

Oh, sorry, I'm not much into 1/8th scale myself, except for my T-Maxx, but that doesn't really count... :D
Forum: RC Nitro Stadium Trucks
07-27-2005, 10:42 PM
Replies: 17
Views: 810
Posted By Jamxx

RE: getting a rush evo to wheelie?

Oh, of course! How could I have forgotten. Keep in mind, a smaller clutchbell/pinion gear and larger spur gear will give you more acceleration.
Forum: RC Nitro Stadium Trucks
07-27-2005, 10:40 PM
Replies: 21,657
Views: 1,514,298
Posted By Jamxx

RE: Official HPI MT2 Thread

Okay, thanks man. I don't know where it is...

I haven't had a problem with ballooning. Perhaps you could try softer springs and less spacers in the front perhaps? Or stiffer ones and more...
Forum: RC Nitro Stadium Trucks
07-27-2005, 08:31 PM
Replies: 21,657
Views: 1,514,298
Posted By Jamxx

RE: Official HPI MT2 Thread

I was wondering if that had ever happened to anyone. I noticed the evil-clip on there and didn't know if that design would hold up well or not. It seems to do pretty well, but I guess it isn't...
Forum: RC Nitro Stadium Trucks
07-27-2005, 06:03 PM
Replies: 21,657
Views: 1,514,298
Posted By Jamxx

RE: Official HPI MT2 Thread

I am so happy. :D

I got it working! I apparently wasn't priming it enough and that pipe was too restrictive for it. Now it starts on the first pull! It is raining here right now, but hopefully...
Forum: RC Nitro Stadium Trucks
07-27-2005, 03:47 PM
Replies: 17
Views: 810
Posted By Jamxx

RE: getting a rush evo to wheelie?

Stiff springs in the back and tighten the feces out of your slipper clutch may make it wheelie. Also, try putting a ton of spacers on the back as well if you don't have stiff springs or put them on...
Forum: RC Nitro Stadium Trucks
07-27-2005, 03:38 PM
Replies: 21,657
Views: 1,514,298
Posted By Jamxx

RE: Official HPI MT2 Thread

I have about 6 inches of fuel line... Well, it began to rain here today, but I'll still try to fix everything today. I'm not frustrated anymore, and I figured out that to fix this, I won't have to do...
Forum: RC Nitro Stadium Trucks
07-27-2005, 12:53 PM
Replies: 6
Views: 500
Posted By Jamxx

RE: New Pipe for a .26 HB LSP.

It depends on what you want. If I am correct, I believe that fatter, shorter pipes help the lower power end more, and the longer, skinnier pipes help the top power end more. There are also ribbed...
Forum: RC Nitro Stadium Trucks
07-27-2005, 12:00 PM
Replies: 21,657
Views: 1,514,298
Posted By Jamxx

RE: Official HPI MT2 Thread

About the knuckle problem, it has been asked many times before. You can melt a nut on the other side as described in an earlier page in this thread, or I just used threadlocker and it seems to be...
Forum: RC Nitro Stadium Trucks
07-26-2005, 10:07 PM
Replies: 21,657
Views: 1,514,298
Posted By Jamxx

RE: Official HPI MT2 Thread

Okay, I know this is off topic, but I like you guys so much and trust you that I have to post this here. Moderators, you understand, right? ;) Thanks in advance.

I am very frustrated at the...
Forum: RC Nitro Stadium Trucks
07-26-2005, 08:18 PM
Replies: 21,657
Views: 1,514,298
Posted By Jamxx

RE: Official HPI MT2 Thread

No, I don't think that's what he meant. He means on the outside of the carburetor, not the inside. Where the carburetor linkage attaches to the ball joint, in that area, there should be a little boot...
Forum: RC Nitro Stadium Trucks
07-26-2005, 12:23 PM
Replies: 21
Views: 1,230
Posted By Jamxx

RE: MT2 .18 SS Flaws...

You put the shims between the bevel gear and its bearing. You need to take the evil-clip off the shaft in which the bevel gear is on and slide it out, then put the shims on top of the bearing. Or,...
Forum: RC Nitro Stadium Trucks
07-26-2005, 12:15 PM
Replies: 21,657
Views: 1,514,298
Posted By Jamxx

RE: Official HPI MT2 Thread

Hey, I'm still here! I had a big day yesterday with 4 of my really good friends, so I didn't have time to do any posting yesterday.

Which also means I haven't run my MT2 any either. However, I...
Forum: RC Nitro Stadium Trucks
07-24-2005, 10:51 PM
Replies: 21,657
Views: 1,514,298
Posted By Jamxx

RE: Official HPI MT2 Thread

Yeah, I thought the .18 for my T-Maxx would be good. The 2.5 engine (in my honest opinion) doesn't have quite enough torque to pull such a heavy truck with that gearing. And I've heard that the O.S....
Forum: RC Nitro Stadium Trucks
07-24-2005, 09:00 PM
Replies: 21,657
Views: 1,514,298
Posted By Jamxx

RE: Official HPI MT2 Thread

Just got back from my lake house. I had a great time bashing this thing around, and nothing broke! How lucky! The only thing inconvenient is that the wheel nuts kept coming loose, and every run or so...
Forum: RC Nitro Stadium Trucks
07-22-2005, 07:27 PM
Replies: 20
Views: 896
Posted By Jamxx

RE: Piston and Sleeve

As a matter of fact, I haven't had any reason to take off the cooling head on my engine, but I need to clean it so I'm going to go do that now. It needs a good scrubdown, there are a few specks of...
Forum: RC Nitro Stadium Trucks
07-22-2005, 07:24 PM
Replies: 21,657
Views: 1,514,298
Posted By Jamxx

RE: Official HPI MT2 Thread

Thanks.

Turns out my front differential started slipping a little bit after I posted that last. Well, it is much easier to get to the front one than the back and I had it shimmed and put back...
Forum: RC Nitro Stadium Trucks
07-22-2005, 07:00 PM
Replies: 43
Views: 1,684
Posted By Jamxx

RE: clean vs. dirty

... That's still dirty in my book. VERY dirty... :D;)
Forum: RC Nitro Stadium Trucks
07-22-2005, 06:51 PM
Replies: 10
Views: 373
Posted By Jamxx

RE: glow plugs? what do u use

I use the McCoy MC9 plugs, not the MC59's. They work pretty well for me.

McCoy MC9 Glow Plug

EDIT: Wait, no, I don't think that's what I use. Mine are made by Dynamite... But it says MC9...
Forum: RC Nitro Stadium Trucks
07-22-2005, 06:47 PM
Replies: 10
Views: 542
Posted By Jamxx

RE: Help a begginer with a Mt2

I really don't think it is your carburetor adjustments. If you can at least get it running and not stalling, you should see much performance than that. At the richest setting on my MT2 that I can...
Forum: RC Nitro Stadium Trucks
07-22-2005, 01:35 PM
Replies: 21
Views: 598
Posted By Jamxx

RE: I know,I know

The fact that you have the power to do this is what irritates me. I probably won't be seeing a new R/C for a year or so. I'll just have to make do with what I have (see signature... hahah!)
Forum: RC Nitro Stadium Trucks
07-22-2005, 01:32 PM
Replies: 43
Views: 1,684
Posted By Jamxx

RE: clean vs. dirty

I don't have an anondized cooling head, so I think it's okay.

Thanks for the tip, D0G, I won't spray it in my eye. ;)
Forum: RC Nitro Stadium Trucks
07-22-2005, 01:26 PM
Replies: 9
Views: 459
Posted By Jamxx

RE: runnig st with two speed

Well said, well said. I'm a wordy talker... :D
Showing results 1 to 25 of 274
 
Page 1 of 11
1
2
3
Last »


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.