RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: gld2
Showing results 1 to 16 of 16
Search took 0.67 seconds.
01-17-2007, 03:55 PM
Replies: 4
Views: 964
Posted By gld2

RE: Dust collector

Thought about using the intake hole for the calculation. Wasn't if sure that would good enough.

Thanks for your input.
01-17-2007, 02:14 PM
Replies: 4
Views: 964
Posted By gld2

Dust collector

I want to build a dust collecting table to do sanding on using this type of collector.

http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=94029


This unit is rated at 914...
01-17-2007, 10:03 AM
Replies: 6
Views: 878
Posted By gld2

Dust collector

I want to build a dust collecting table to do sanding on using this type of collector.

http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=94029


This unit is rated at 914...
09-18-2005, 09:09 PM
Replies: 7
Views: 837
Posted By gld2

RE: Victor Didelot

Thanks for the help fellows.

What is "Sam Speaks" and where to get it????
09-18-2005, 03:14 PM
Replies: 7
Views: 837
Posted By gld2

RE: Victor Didelot

Sorry to here of his passing..... So now where do I go to get ignition parts for antique Ohlsson & Rice 60 engine????
09-17-2005, 07:10 PM
Replies: 7
Views: 837
Posted By gld2

Victor Didelot

Hi all,

I mailed a letter to Mr. Didelot to order some egine parts. The address I used (4410 Lorna Lane Erie, Pa. 16506)..

The letter came back (Not deliverable as addressed).

Could...
12-07-2004, 02:36 PM
Replies: 7
Views: 1,507
Posted By gld2

RE: Speed 400

Here's the story. I found this electric C-130 plan in dfx format. It calls for four speed 400's direct drive 6-3 props and a 10 cell nicad. I bench checked one motor for amp draw and it showed 9...
12-06-2004, 10:14 PM
Replies: 7
Views: 1,507
Posted By gld2

Speed 400

Can anyone tell me how much current a speed 400 7.2 volt with a direct drive 6-3 prop on 12 volts will draw.

Gary
12-01-2004, 12:52 PM
Replies: 0
Views: 440
Posted By gld2

CoverLite

I want to make decals out of CoverLite to apply over CoverLite.
My question is, will this distort the airframe CoverLite to the point it can not be reshrunk successfully, and not mess up the decal....
11-23-2004, 10:41 PM
Replies: 4
Views: 791
Posted By gld2

RE: Airfoil

Never thought to check that data base. Have got several dat from files there.

It's hard to see the forest for tree's. HA

I'll check there first next time.

Thanks
11-23-2004, 09:18 AM
Replies: 4
Views: 791
Posted By gld2

Airfoil

Hi
Anyone out there happen to have the airfoil co-ordinates for the
Goldberg Falcon 56. I can scan and trace, but there is always errors
in that procedure.
02-05-2004, 02:10 PM
Replies: 2
Views: 1,702
Posted By gld2

RE: Zagi CG

Thanks Paul. I'll try both ways, if it ever quits snowing up here. 14" and counting.
02-05-2004, 10:47 AM
Replies: 2
Views: 1,702
Posted By gld2

Zagi CG

Is the method of finding the CG of a tapered wing good to use on the Zagi?????

If it is, that puts the CG about 3" farther back than what is recomended on this plan.
...
12-02-2003, 05:00 PM
Replies: 2
Views: 561
Posted By gld2

Triron charger

I have a new Triton charger purchased Nov. 10, and a new lipoly battery (2s1p 1200mah). I was told to charge this battery at 1.2 amp, 8.4v, but there is no 8.4v setting on the Triton. So I called the...
Forum: The Clubhouse
03-01-2003, 09:35 AM
Replies: 4
Views: 726
Posted By gld2

StarCad Plans

Howard
Thanks for the reply. I tried to reply to your e-mail and it came back undelivered.
Do you know if StarCadPlans are gone for good, or just reorganizing.

Gary

http://www.gldpages.com
Forum: The Clubhouse
02-28-2003, 10:19 AM
Replies: 4
Views: 726
Posted By gld2

Plans CD

Anyone know what happened to StarCadPlans? There web address brings
up a different page now.

http://www.starcadplans.com/

If you have info, please contact me off list.

Thanks
Gary Davison...
Showing results 1 to 16 of 16


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.