RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 9
1
2
3
Last »
Search: Posts Made By: Henning
Showing results 1 to 25 of 212
Search took 0.71 seconds.
Forum: Electric Pattern Aircraft
04-12-2020, 11:52 AM
Replies: 2,031
Views: 683,449
Posted By Henning

Thanks Will! Yes, the Accuracy is built from...

Thanks Will!

Yes, the Accuracy is built from a Naruke Kit originally for YS but I have redesigned it from one piece wing to plugin wings. The T-can is from a CA Osmose. It improves the rudder...
Forum: Electric Pattern Aircraft
04-11-2020, 05:17 AM
Replies: 2,031
Views: 683,449
Posted By Henning

Hi Peter An alternative to adding a sleve...

Hi Peter

An alternative to adding a sleve over the dampers to limit movement is to increase the diameter of the rubber dampers and keeping the hight. I went up from D10 mm to D15 mm and reduced...
Forum: Electric Pattern Aircraft
04-10-2020, 12:32 PM
Replies: 2,031
Views: 683,449
Posted By Henning

Hi Peter, The parts for the mount for sure...

Hi Peter,

The parts for the mount for sure looks good when cut by CNC. I still cut my mounting plates with a scroll saw and drill with a drill press. I am still experimenting to to improve the...
Forum: Electric Pattern Aircraft
01-01-2020, 01:26 PM
Replies: 2,031
Views: 683,449
Posted By Henning

Hi Dave and Peter, The weather over the...

Hi Dave and Peter,

The weather over the x-mas holiday has been good enough to test the D3 ESC. We only have 4 hours of flyable daylight at this time of the year but over some days I have logged 29...
Forum: Electric Pattern Aircraft
12-21-2019, 02:18 PM
Replies: 2,031
Views: 683,449
Posted By Henning

Thanks Dave I installed the D3 ESC today in...

Thanks Dave

I installed the D3 ESC today in my old trusty Accuracy Mono from Naruke Hobby that will be my testbed over the winter. Looking at your Normal throttle curve I will have to do some...
Forum: Electric Pattern Aircraft
12-08-2019, 03:16 AM
Replies: 2,031
Views: 683,449
Posted By Henning

Thanks Peter, Hopefully over x-mas it will...

Thanks Peter,

Hopefully over x-mas it will be up and running.


Br

Henning
Forum: Electric Pattern Aircraft
11-27-2019, 10:28 AM
Replies: 2,031
Views: 683,449
Posted By Henning

Hi Peter Are you using a Futaba Tx with the...

Hi Peter

Are you using a Futaba Tx with the D3? If yes what ATVs are you using? What do you use at landing? Idle-up switch or a different throttle curve? It would be great if you could please...
Forum: Electric Pattern Aircraft
11-23-2019, 06:48 AM
Replies: 2,031
Views: 683,449
Posted By Henning

Hi Ted, I have already bought one from him...

Hi Ted,

I have already bought one from him but due to lack of time I have not mounted it in my plane yet. I was just queries if someone had tested it with the V4. I have seen several D3s used with...
Forum: Electric Pattern Aircraft
11-23-2019, 01:58 AM
Replies: 2,031
Views: 683,449
Posted By Henning

Hi, Anyone tried the D3 ESC from Adam...

Hi,

Anyone tried the D3 ESC from Adam Dębowski with the V4-Pyro 600?


Br
Henning
Forum: Electric Pattern Aircraft
05-31-2019, 11:51 AM
Replies: 2,031
Views: 683,449
Posted By Henning

https://cimg8.ibsrv.net/gimg/www.rcuniverse.com-vb...

https://cimg8.ibsrv.net/gimg/www.rcuniverse.com-vbulletin/768x1024/unadjustednonraw_thumb_104d_cf95ea899b61b0dad054f05a2fd93bc187a112d6.jpg...
Forum: Electric Pattern Aircraft
10-24-2018, 11:16 AM
Replies: 2,031
Views: 683,449
Posted By Henning

Hi Paul, 22” is less noisy than 23”...

Hi Paul,

22” is less noisy than 23” regardless of brand. I used the Mejzlik 22x22R and 22x20F in the semi finals at the WC in Argentina flying a Naruke Ascent Bip in 14,7 m/s cross wind. I pulled...
Forum: Electric Pattern Aircraft
10-24-2018, 09:20 AM
Replies: 2,031
Views: 683,449
Posted By Henning

Hi Paul, Yes, I have been using the Mejzlik...

Hi Paul,

Yes, I have been using the Mejzlik 22x22R and 22x20F with the V4/Pyro 600. They work very well in windy conditions. They give more speed per mAh used than Falcon 23x20F 23x20R. In calm...
Forum: Electric Pattern Aircraft
01-26-2018, 01:36 PM
Replies: 2,031
Views: 683,449
Posted By Henning

I flew for the first time today with the new...

I flew for the first time today with the new upgrade gear set for the V4. What a difference. It is really quiet compare to the old gears. My flying buddy was flying with the V4 and old gear set and...
Forum: Electric Pattern Aircraft
11-02-2017, 02:22 PM
Replies: 48
Views: 26,839
Posted By Henning

My Ascent looks small….

My Ascent looks small….
Forum: Electric Pattern Aircraft
08-11-2017, 10:37 AM
Replies: 2,031
Views: 683,449
Posted By Henning

My setup: Mezon 95 Lite Timing 24 Poles...

My setup:
Mezon 95 Lite

Timing 24
Poles 14
Startup -50
Break full 30% init 16% 0,7s 0,7s
End point full 1,96 start 1.1
Max amp 90
Max temp 90 degrees C
Forum: Electric Pattern Aircraft
05-13-2017, 01:02 PM
Replies: 2,031
Views: 683,449
Posted By Henning

Hey Brenner, What is the benefit of running...

Hey Brenner,

What is the benefit of running 22x20 front and 23x22 rear compared to 23” on both props?

My current favourite propellers are Falcon 23x20F and 23x22R. I find my planes to feel more...
Forum: Electric Pattern Aircraft
01-16-2017, 11:14 AM
Replies: 2,031
Views: 683,449
Posted By Henning

Was this with full throttle or do you have the...

Was this with full throttle or do you have the ATV reduced and or a Throttle Tech sensor?


I have not done any sound checks yet but will be surprised if if don´t pass the sound check with the...
Forum: Electric Pattern Aircraft
01-15-2017, 08:06 AM
Replies: 2,031
Views: 683,449
Posted By Henning

How will the extra weight affect flight...

How will the extra weight affect flight performance and the life of the motor bearings compared to
2 x 50 grams props?


Br,
Henning
Forum: Electric Pattern Aircraft
12-11-2016, 03:03 AM
Replies: 2,031
Views: 683,449
Posted By Henning

http://www.rcuniverse.com/forum/attachment.php?att...

http://www.rcuniverse.com/forum/attachment.php?attachmentid=2193094
Hi,


I did some temp. measurements with the new aluminium front plate installed and it looks like it helps. I will need more...
Forum: Electric Pattern Aircraft
11-30-2016, 01:34 PM
Replies: 2,031
Views: 683,449
Posted By Henning

http://www.rcuniverse.com/forum/attachment.php?att...

http://www.rcuniverse.com/forum/attachment.php?attachmentid=2191825http://www.rcuniverse.com/forum/attachment.php?attachmentid=2191826
Hi,


My last update to the motor mount has been to cut a...
Forum: Electric Pattern Aircraft
11-06-2016, 01:50 AM
Replies: 2,031
Views: 683,449
Posted By Henning

Hi Peter, The bearings do not absorb much...

Hi Peter,


The bearings do not absorb much axial load as most forces are transferred by the standoffs to the back support. How long the bearings will last I do not know. I have only approx. 100...
Forum: Electric Pattern Aircraft
10-15-2016, 01:28 PM
Replies: 2,031
Views: 683,449
Posted By Henning

Thanks Brenner! The ESC is located just...

Thanks Brenner!


The ESC is located just behind a air inlet at the front so it has got cooling from two directions. I am using the Mezon 95 Opto light. The temperature of the ESC with the Pyro...
Forum: Electric Pattern Aircraft
10-15-2016, 10:09 AM
Replies: 2,031
Views: 683,449
Posted By Henning

With proper ducting of cooling air to the motor...

With proper ducting of cooling air to the motor the temperature went down from “too hot to touch after a flight” to below body temperature.

I created two plugs of foam and covered them with...
Forum: Electric Pattern Aircraft
10-07-2016, 11:11 AM
Replies: 2,031
Views: 683,449
Posted By Henning

Hi, I flew 1 round P17 and 6 F17 today....

Hi,


I flew 1 round P17 and 6 F17 today. The change from the supplied sloppy needle bearing to two tight ball bearings had two positive effects. The plane rolls more axial and the noise level is...
Forum: Electric Pattern Aircraft
10-06-2016, 11:08 AM
Replies: 2,031
Views: 683,449
Posted By Henning

http://www.rcuniverse.com/forum/attachment.php?att...

http://www.rcuniverse.com/forum/attachment.php?attachmentid=2184662
Hi,


I changed the needle back support bearing to two high quality 6x10x3 mm ball bearings + a spacer to fill the gap in the...
Showing results 1 to 25 of 212
 
Page 1 of 9
1
2
3
Last »


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.