RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: arendall
Showing results 1 to 12 of 12
Search took 0.51 seconds.
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
10-27-2005, 03:00 PM
Replies: 0
Views: 455
Posted By arendall

$200 Reward

We are looking for the person or persons responsible for a break in at Fullers R/C Hobbies.

If you have any info on this person trying to sell this stuff please let us know.

visit...
Forum: Electric RC Helis
10-27-2005, 02:58 PM
Replies: 5
Views: 759
Posted By arendall

RE: $200 Reward

Thank you for your replys .. and i dont know about his insurance, all i do is his website and i have notified the local club and flyers in the area.
Forum: Electric RC Helis
10-27-2005, 05:19 AM
Replies: 5
Views: 759
Posted By arendall

RE: $200 Reward

Thank you
Forum: Electric RC Helis
10-25-2005, 05:23 AM
Replies: 5
Views: 759
Posted By arendall

$200 Reward

We are looking for the person or persons responsible for a break in at Fullers R/C Hobbies.

If you have any info on this person trying to sell this stuff please let us know.

visit...
Forum: Electric RC Helis
10-20-2005, 04:14 AM
Replies: 5
Views: 762
Posted By arendall

RE: blade cp and the carbin fiber blades

thank you for that info and it makes sense, but i went ahead and put them on for a trial flight before you posted and i could not tell much diferance in the flight of the heli.
but i did put the...
Forum: Electric RC Helis
10-20-2005, 01:03 AM
Replies: 2
Views: 521
Posted By arendall

RE: Help with my eflite blade cp wont lift

there is a lot you have to look at first is the trim settings and if you pull back on the right stick does the back of the craft sit back down.
therfor i would check my servo first off.
Forum: Electric RC Helis
10-20-2005, 12:27 AM
Replies: 5
Views: 762
Posted By arendall

blade cp and the carbin fiber blades

i have read that you can not run the carbon fiber blades on a stock Blade CP.
i can not tell much diff. in weight of the wood and the carbon fiber so why can you not just change them out?
Forum: Electric RC Helis
10-16-2005, 11:06 PM
Replies: 1
Views: 335
Posted By arendall

RE: Trimmed all the way and tail still swing left.

the front pot is for the gyro i would leave it alone at first and the back one is for the tail rotor adjust it only about 1/8 turn at a time make sure to unplug the bat. then make adjustment plug in...
Forum: Electric RC Helis
10-16-2005, 10:51 PM
Replies: 2
Views: 486
Posted By arendall

RE: Blade cp swashplates

that thread does not have anything on the settings of the paddel itself...
Forum: Electric RC Helis
10-16-2005, 09:30 PM
Replies: 2
Views: 394
Posted By arendall

RE: Blade CP 4 in 1 adjustement

oh and on mine i adjusted only 1/8 turn at a time..
Forum: Electric RC Helis
10-16-2005, 09:29 PM
Replies: 2
Views: 394
Posted By arendall

RE: Blade CP 4 in 1 adjustement

the back pot on the 4 in 1 should adjust the center of the tail rotor.
but it will not do anything untill you unplug the bat. and let it set for a sec or 2 the plug it back in.
Forum: Electric RC Helis
10-15-2005, 08:14 PM
Replies: 2
Views: 486
Posted By arendall

Blade cp swashplates

my question is how to set the swashplates ?
i have went throught the book exactly how it says but does not say anything about the set of the sp.
setting still no throtal it is slightly pitched...
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.