RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 20
1
2
3
11
Last »
Search: Posts Made By: Nick Yuhasz
Showing results 1 to 25 of 500
Search took 0.87 seconds.
Forum: Airplanes - All types
02-29-2024, 01:36 PM
Replies: 0
Views: 199
Posted By Nick Yuhasz

*FS CompArf EuroSport Intake Ducts and bypass

Composite ARF Eurosport Full Intake Duct and bypass
Previously installed in a partially completed Eurosport jet I purchased. I have included new Velcro strapping for the engine bypass. It is in...
Forum: RC Jets
11-21-2023, 12:32 PM
Replies: 71
Views: 164,850
Posted By Nick Yuhasz

Nice pics of your build! As for the location of...

Nice pics of your build! As for the location of the UAT / Fuel Pump, I located mine in the same spot for a very specific purpose, that is, if I ever wanted to separate the fuse for transport, all...
Forum: RC Jets
11-17-2023, 02:39 PM
Replies: 71
Views: 164,850
Posted By Nick Yuhasz

I did not glue the Tip Tanks - just made sure the...

I did not glue the Tip Tanks - just made sure the clamps were tight Also a little blue Loctite on the aluminum retention shafts.

Nick
Forum: RC Jets
11-17-2023, 10:45 AM
Replies: 71
Views: 164,850
Posted By Nick Yuhasz

Mpizpilot Your L-39 is looking good! I took one...

Mpizpilot Your L-39 is looking good! I took one elevator to Home Depot and had them computer match the colors and make up small samples - worked well, very close match.

Nick
Forum: Futaba Radios Direct support forum
11-13-2023, 05:02 PM
Replies: 0
Views: 430
Posted By Nick Yuhasz

R7108SB and R7208SB capable of SBus & SBus2?

With my 18SZ, I want to use an iGyro SRS. Previously I set protocol to FASST, use a FASST receiver (R6208SB), and connect the SBus receiver port to the iGyro SRS.
Now I want to use a FASSTest...
Forum: RC Jets
11-01-2023, 10:51 AM
Replies: 71
Views: 164,850
Posted By Nick Yuhasz

Dror: It has been a while since I finished the...

Dror: It has been a while since I finished the L-39, but here is how I remember routing the wires. Wires from the wing tip lights and the aileron servo were routed along the rear of the wing to the...
Forum: RC Jets
06-23-2023, 05:06 AM
Replies: 71
Views: 164,850
Posted By Nick Yuhasz

Thanks, Gary! Nick

Thanks, Gary!

Nick
Forum: RC Jets
06-22-2023, 10:15 AM
Replies: 71
Views: 164,850
Posted By Nick Yuhasz

Finally a maiden flight for my new, TopRC jet...

Finally a maiden flight for my new, TopRC jet turbine L-39 at Michigan’s “Midwest Jet Pilot’s Spring Fling” on June 8, 2023. I want to thank Gator RC, Cap’n Dave Murray, Eddie Bernaldez, and Steven...
Forum: RC Jets
05-07-2023, 03:48 PM
Replies: 71
Views: 164,850
Posted By Nick Yuhasz

I have not had any issues with the stock brake...

I have not had any issues with the stock brake controller and any control surfaces (at least not on the ground - have not maidened it yet). I am using all separate A123 batteries for brakes, lights,...
Forum: KingTech Turbines International
04-16-2023, 02:56 PM
Replies: 0
Views: 622
Posted By Nick Yuhasz

K-170 G2 Xicoy V10 ECU codes?

So I flew one of my jets over the weekend with an oldy, but a goody K-170 G2 Xicoy V10 ECU. I had a flameout without white smoke and dead sticked the aircraft in with no issue.

Came home and...
Forum: RC Jets
02-14-2023, 02:17 PM
Replies: 62
Views: 12,246
Posted By Nick Yuhasz

Still flying my original Futaba 14MZ I received...

Still flying my original Futaba 14MZ I received in February 2005 which started as 72Mhz and was upgraded to 2.4Ghz. I believe I was the first person to fly turbine jets with the 14MZ transmitter in...
Forum: RC Jets
01-02-2023, 04:24 PM
Replies: 71
Views: 164,850
Posted By Nick Yuhasz

Thank you for the compliment! I got the pilot...

Thank you for the compliment! I got the pilot from www.warbirdpilots.com

Nick
Forum: RC Jets
12-27-2022, 04:46 PM
Replies: 71
Views: 164,850
Posted By Nick Yuhasz

Decided to mount the tip tank Unilights...

Decided to mount the tip tank Unilights (spotlight, nav light, and ACL). The internal structure of the tip tanks make routing the wiring easy. I used ZAP Goo to mount the light fixtures in the odd...
Forum: RC Jets
12-23-2022, 04:22 AM
Replies: 71
Views: 164,850
Posted By Nick Yuhasz

You are correct, Kevlar would have been a better...

You are correct, Kevlar would have been a better solution. I am planning on using a second receiver placed away from the CF.

Thanks for the feedback.

Nick
Forum: RC Jets
12-22-2022, 12:12 PM
Replies: 71
Views: 164,850
Posted By Nick Yuhasz

Here is a picture of the main control board...

Here is a picture of the main control board containing one of the two receivers, the iGyro SRS, the Unilight controller, and the TopRC retract / brake controller. I will add the 2nd receiver and the...
Forum: RC Jets
12-21-2022, 05:43 PM
Replies: 71
Views: 164,850
Posted By Nick Yuhasz

The next task I decided to do may be...

The next task I decided to do may be controversial. I decided to strengthen the area under the canopy with carbon fiber cloth that I had.

There is a 2 foot section, under the canopies, between...
Forum: RC Jets
12-18-2022, 06:36 PM
Replies: 71
Views: 164,850
Posted By Nick Yuhasz

Back in Ohio again so on to mounting main...

Back in Ohio again so on to mounting main switches / charging jacks and A123 batteries.

I decided to mount the two receiver power switches, the lighting / smoke pump switch, and the retract /...
Forum: RC Jets
11-26-2022, 11:32 AM
Replies: 71
Views: 164,850
Posted By Nick Yuhasz

Dreamworks sells the fuel tank fittings - well...

Dreamworks sells the fuel tank fittings - well worth the cost. And, yes, you did pronounce my last name correctly!

Nick
Forum: RC Jets
11-21-2022, 03:52 PM
Replies: 71
Views: 164,850
Posted By Nick Yuhasz

I used thread with a small fishing lead weight on...

I used thread with a small fishing lead weight on the end to "fish" it through from the top of the fin where the strobe will go to the base. Yes, it took a very, very long time. I tilted the fin...
Forum: RC Jets
11-14-2022, 06:41 AM
Replies: 71
Views: 164,850
Posted By Nick Yuhasz

Time to finish the wings: First, the flaps. The...

Time to finish the wings: First, the flaps. The four hinges per flap have pre-cut slots in the wing and flaps; a great time saver. On my jet as delivered, the pre-cut slots appeared to place the...
Forum: RC Jets
11-08-2022, 05:11 PM
Replies: 71
Views: 164,850
Posted By Nick Yuhasz

Next up: the nose gear and the next minor...

Next up: the nose gear and the next minor challenge of the build as you will see. First, the nose gear door needs to be trimmed slightly to allow it to open all the way and not interfere with the...
Forum: RC Jets
11-05-2022, 02:58 PM
Replies: 71
Views: 164,850
Posted By Nick Yuhasz

Decided to mount all "wet" items (smoke and fuel...

Decided to mount all "wet" items (smoke and fuel tanks, pumps, and UAT) in the rear section of the fuselage. Greatly simplified the build and if I ever have to split the fuse for transport or...
Forum: RC Jets
11-01-2022, 05:19 PM
Replies: 71
Views: 164,850
Posted By Nick Yuhasz

So first hurdle with the build: You will discover...

So first hurdle with the build: You will discover that with the main fuel tank in place on it's mounting platform and back against the wing tube, it will interfere with the rear cockpit going in...
Forum: RC Jets
11-01-2022, 05:53 AM
Replies: 71
Views: 164,850
Posted By Nick Yuhasz

Decided I would run all the wiring to the rear of...

Decided I would run all the wiring to the rear of the jet. Rudder, both elevators, and fin lighting 20 ga wiring were encapsulated in heat-resistant Cool Tube Extreme until past the turbine mounts...
Forum: RC Jets
10-16-2022, 06:25 AM
Replies: 71
Views: 164,850
Posted By Nick Yuhasz

A relatively easy task is to install the Speed...

A relatively easy task is to install the Speed Brake servo. I decided to utilize an older JR 8611 servo. The supplied control rod and ball links would probably be sturdy enough, but I decided to...
Showing results 1 to 25 of 500
 
Page 1 of 20
1
2
3
11
Last »


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.