RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Search
Today's Posts
Mark Forums Read
Vendor Directory
Notices
Search: Posts Made By: poypoy
Showing results 1 to 17 of 17
Search took 0.46 seconds.
Forum: Electric Pattern Aircraft
07-30-2012, 06:05 PM
Replies: 134
Views: 47,699
Posted By poypoy

RE: New Griffin by Xtreme Composite

.....still on the subject on snaps, are they crisp and stops on a dime? ...spins? ... is it slow on downlines? does rudder have authority on knife edge manuevers?

poy ilano
Forum: ARF or RTF
02-01-2010, 07:43 PM
Replies: 3
Views: 812
Posted By poypoy

RE: ARF mfg Yak54-50-3D - Anyone got one?

how bad is the covering? does it easily peel off in flight? are there other threads that you know of with regards to this subject (ARF mfg yak 55 26 cc)? I am about to get a goldwingrc (formerly ARF...
Forum: RC Pattern Flying
01-11-2010, 07:27 PM
Replies: 804
Views: 118,421
Posted By poypoy

RE: Excelleron 90

Thanks guys for your prompt replies.
I planning to install a 120SC ..but it would be more convenient for me to just install a screw in muffler rather than make a tunnel for a pipe. Do you have an...
Forum: RC Pattern Flying
01-10-2010, 05:01 PM
Replies: 804
Views: 118,421
Posted By poypoy

RE: Excelleron 90

to Allan or to anyone using a YS 1.20 on the excelleron. what muffler are you using? ...and if a tuned pipe is used, can it be tunneled thru the fuse and wing belly pan? any other suggestions how to...
Forum: 3D Flying!
03-23-2008, 04:24 PM
Replies: 11
Views: 1,055
Posted By poypoy

RE: Fliton edge 540 please help!

steven, just slide it just enough to clear the rubber bands ..cuz you also want to keep your tank to as close to the CG as possible.
Forum: 3D Flying!
03-23-2008, 03:58 PM
Replies: 11
Views: 1,055
Posted By poypoy

RE: Fliton edge 540 please help!

Yup, i used a dremel to conform the former to the contours of the bottom of the tank, thus acting as a cradle.
However, if you dont want to touch the formers, you may change the tank into a...
Forum: 3D Flying!
03-23-2008, 06:28 AM
Replies: 11
Views: 1,055
Posted By poypoy

RE: Fliton edge 540 please help!

Steven, in fairness to fliton, their stock tank and set up does work just fine on my side mounted OS 91FSII w pump. It hits the recommended cg perfectly in paper and in flight. The engine runs...
Forum: JR Radio & Spektrum Radios
03-10-2008, 05:47 AM
Replies: 0
Views: 491
Posted By poypoy

snap roll flight condition for 10sxII (heli)

Please assist me with this predicament of mine. I had a 10S (airplane version) which i damaged and assesed "too expensive to repair " prompting me to use my SXII (HELI version) on my pattern fixed...
Forum: YS Engines Support
03-08-2008, 07:35 PM
Replies: 14
Views: 1,566
Posted By poypoy

RE: 2 Fuel tanks

Troy, your explanation on the header topic was really informative, thanks ... & i do hope you will recover from your symptoms soon.

since we are still on the bubbles issue, can anyone please...
Forum: YS Engines Support
03-08-2008, 06:40 PM
Replies: 3
Views: 801
Posted By poypoy

RE: DZ160: hard 1st start of the day

thanks Troy for your response.
Definitely this is a fuel draw problem, but is it just a priming problem? ...or is it a pump problem? when would i need to change my the diaphragm?
yup, i do run a...
Forum: YS Engines Support
03-08-2008, 12:37 PM
Replies: 3
Views: 801
Posted By poypoy

DZ160: hard 1st start of the day

I have this problem of hard starting a 160DZ , but only during its 1st start of the day. I know that unlike other YS engines, it does not have a pressurized system and it would usually need a good...
Forum: RC Pattern Flying
03-08-2008, 10:09 AM
Replies: 16
Views: 4,124
Posted By poypoy

RE: Hyde Mounts

Brandon, how do we order direct from merle hyde? ..does he have a website? ..e-mail address?
I have difficulty deciding which mount to use on my composite shinden w ys170. thanks
Forum: RC Pattern Flying
03-01-2008, 07:23 AM
Replies: 13
Views: 1,712
Posted By poypoy

RE: P-09 woes

Thanks Bryan, i have solved my snap problem as you suggested, ..by increasing my aileron throws, giving just enough (not full) elevators and rudder. I did both positive and negative snaps and i...
Forum: RC Pattern Flying
03-01-2008, 07:12 AM
Replies: 13
Views: 1,712
Posted By poypoy

RE: P-09 woes

"the outside half loops begin immediately after the 2/4 pt and full roll ....and the lenght of the upper horizontal line , including the rolls ,is equal to the diameter of the half loops." - This...
Forum: RC Pattern Flying
02-29-2008, 01:07 PM
Replies: 13
Views: 1,712
Posted By poypoy

RE: P-09 woes

I dont wish to complicate the p-o9 schedule, but another concern of mine are the half rolls. unless specified as reversing, is it safe to assume that the half rolls (particularly in the triangle...
Forum: RC Pattern Flying
02-29-2008, 12:32 PM
Replies: 13
Views: 1,712
Posted By poypoy

RE: P-09 woes

thanks guys for your snappy response, no pun intended.

I refered to the 2008 FAI sporting code and indeed, there was no mention wether the snaps are positive or negative for manuever#9. and...
Forum: RC Pattern Flying
02-29-2008, 10:44 AM
Replies: 13
Views: 1,712
Posted By poypoy

P-09 woes

I need help doing manuever #9 particularly the downline 1 1/4 snap of which i have difficulty exiting the snap nose down.
my focus always tends to pitch up and slightly to the right after a right...
Showing results 1 to 17 of 17


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.