RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: rtayloria
Showing results 1 to 14 of 14
Search took 0.50 seconds.
Forum: Speed - RC Nitro Boats
07-04-2006, 11:53 PM
Replies: 4,067
Views: 450,337
Posted By rtayloria

RE: AquaCraft U-18 Miss Vegas Hydro Thread_Make it Fast!

QUick question gentlemen. Anyone know what the engine temp should be after a couple of high speed passes? My main issue last time I was at the lake was a fouled glo-plug, but I have replacements now,...
Forum: RC Nitro Stadium Trucks
07-02-2006, 08:19 PM
Replies: 5
Views: 532
Posted By rtayloria

RE: Jato 2.5 Issues

Also just to note that in the 20 or so tanks I have ran through I have left the high speed needle at the factory setting. When it started dieing today I adjusted to richen it up a bit, about 1/2 turn...
Forum: RC Nitro Stadium Trucks
07-02-2006, 08:07 PM
Replies: 5
Views: 532
Posted By rtayloria

RE: Jato 2.5 Issues

Not a temp gun, but a temp probe that is very sensitive. It is on my multimeter and detects temp changes when the wind blows. This may not be the best thing to use after reading allot of the threads,...
Forum: RC Nitro Stadium Trucks
07-02-2006, 07:12 PM
Replies: 5
Views: 532
Posted By rtayloria

RE: Jato 2.5 Issues

Even if they start with no issue the glow plugs can still be the culprit? I thought they were only for starting. After some adjusting I have the wifes running great, but mine will not idle. It will...
Forum: RC Nitro Stadium Trucks
07-02-2006, 04:28 PM
Replies: 5
Views: 532
Posted By rtayloria

Jato 2.5 Issues

Hey gang,
Ran on a great dirt track today, the temp was 93 and the humidty could kill a full grown man. The cars ran great early and then after a few laps started dieing. I tried to richen them...
Forum: Speed - RC Nitro Boats
06-30-2006, 08:34 PM
Replies: 4,067
Views: 450,337
Posted By rtayloria

RE: AquaCraft U-18 Miss Vegas Hydro Thread_Make it Fast!

mounted the S&B y535 today and still had some issue with keeping the boat in the water, but it did have more grab in the corner. The issue I am having with the stock 18 is that now when I lean it out...
Forum: Speed - RC Nitro Boats
06-27-2006, 03:00 PM
Replies: 4,067
Views: 450,337
Posted By rtayloria

RE: AquaCraft U-18 Miss Vegas Hydro Thread_Make it Fast!

Hey gang,
I am going to put on the Octura S&B y535 this weekend and test to see if the boat runs better (I am sure it will). As for the heat issue I am burning a header coupling after several...
Forum: Speed - RC Nitro Boats
06-27-2006, 08:29 AM
Replies: 4,067
Views: 450,337
Posted By rtayloria

RE: AquaCraft U-18 Miss Vegas Hydro Thread_Make it Fast!

t munn,
I have had this problem of late. I have been replacing these after each run as the heat is overwhelming even when running extremely rich. Anyone else have this issue, or a remedy?

...
Forum: Speed - RC Nitro Boats
06-23-2006, 10:52 PM
Replies: 4
Views: 582
Posted By rtayloria

RE: Where to get a roll....

Ron,
I am presently using "Team Associated" Exhaust tubing No.7733, and it works fine, but I would like to be able to purchase a like product by the roll. This product comes in about a 3inch...
Forum: Speed - RC Nitro Boats
06-23-2006, 10:36 PM
Replies: 4
Views: 582
Posted By rtayloria

Where to get a roll....

Where is the best place to find a roll of tubing about 3/4 inches in ouside diameter to connect from the exhaust manifold to the header? I am runnnin a MissVegas and I am using RC Car silicone...
Forum: Speed - RC Nitro Boats
06-11-2006, 11:59 PM
Replies: 4,067
Views: 450,337
Posted By rtayloria

RE: AquaCraft U-18 Miss Vegas Hydro Thread_Make it Fast!

Thanks very much!! Will give my run report hopefully with video attached in the next couple of days... One last thing, how do you explain the sunburn after calling out of work sick?? Thanks for all...
Forum: Speed - RC Nitro Boats
06-11-2006, 11:40 PM
Replies: 4,067
Views: 450,337
Posted By rtayloria

RE: AquaCraft U-18 Miss Vegas Hydro Thread_Make it Fast!

Jerry/Ron,
Thanks for the info! I just ordered 2 sharpened/balanced y535's and one M435/3 (to test) Hopefully this will improve my pitfalls. Now to the next issue I could use some help on. If...
Forum: Speed - RC Nitro Boats
06-11-2006, 01:49 PM
Replies: 4,067
Views: 450,337
Posted By rtayloria

RE: AquaCraft U-18 Miss Vegas Hydro Thread_Make it Fast!

Gentlemen,
I just recently purchased the Miss Vegas and had a question as the boating club that I joined has some pretty die hard members and have instructed me to purchase a metal prop for the...
Forum: Speed - RC Nitro Boats
06-04-2006, 09:09 PM
Replies: 5
Views: 783
Posted By rtayloria

Miss Vegas setup help...

Miss Vegas

Hi all,
I purchased a Miss Vegas in UT Orange (of course, Iā€™m a VOL) and ran the 6 tanks through the motor and during this time had some really great runs. During this time I...
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.