RCU Forums - Search Results

Search: Posts Made By: R Barnette

Showing results 1 to 9 of 9
Search took 0.65 seconds.

Forum: Golden Age, Vintage & Antique RC

03-01-2010, 11:46 PM

Replies: 36

Lance Machining RV-3

Views: 6,380

Posted By R Barnette

RE: Lance Machining RV-3

I have parts for the lance RV 3 and the lance special, wing skins, plastic molded parts and some unused foam wings.
Ralph
[email protected]

Forum: "1/2 A" & "1/8 A" airplanes

02-23-2010, 08:43 PM

Replies: 29

3 Cyl 049 radial

Views: 5,387

Posted By R Barnette

RE: 3 Cyl 049 radial

E-MAIL ME IF YOU WANT THE ENGINE TO RUN. You may try typing Barnette Radial in the search, At one time there were several pictures of my engines in the 1/2 A form
[email protected]
Ralph

Forum: "1/2 A" & "1/8 A" airplanes

12-21-2006, 11:47 PM

Replies: 4

Avro 504

Views: 816

Posted By R Barnette

RE: Avro 504

The Avro is a 504N which had a radial engine, Peter Rake published the prints in Flying Scale Models a few years back.
The airframe weighs 10oz less engine and radio, 36" WS, pull, pull controls,...

Forum: "1/2 A" & "1/8 A" airplanes

12-11-2006, 10:16 PM

Replies: 10

1911 Caudron

Views: 1,984

Posted By R Barnette

RE: 1911 Caudron

I built the engine as a twin then I saw a picture of the Caudron in a English magazine and rebuilt it as a X radial . I scaled the airplane to the engine size, WS 38" airframe weight less engine and...

Forum: "1/2 A" & "1/8 A" airplanes

09-18-2005, 04:12 AM

Replies: 7

Radial

Views: 1,174

Posted By R Barnette

Radial

Check out this web site for a cox radial
www.widecanyonengines.com

Forum: "1/2 A" & "1/8 A" airplanes

09-18-2005, 03:15 AM

Replies: 57

Cox Radial

Views: 12,451

Posted By R Barnette

RE: Cox Radial

If any one is interested in a small radial, or would like to see larger 3&5 cylinder engines up to 2ci so far.
E-mail me at [email protected] or call 662-622-7136.
I hope to build about ten for...

Forum: Glow Engines

09-18-2005, 01:03 AM

Replies: 3,922

Everything Radial Engines

Views: 800,249

Posted By R Barnette

RE: Everything Radial Engines

I build my own two cycle radials of various sizes, it is a lots cheaper, just takes a little time to make one.
Ralph
[email protected]

Forum: Glow Engines

09-18-2005, 12:48 AM

Replies: 7

Looking for Webra 32 info

Views: 3,851

Posted By R Barnette

RE: Looking for Webra 32 info

I have hundreds of new parts for the Speed and Silverline/Blackhead engines
Thanks
Ralph

Forum: "1/2 A" & "1/8 A" airplanes

09-16-2005, 10:17 PM

Replies: 57

Cox Radial

Views: 12,451

Posted By R Barnette

Cox Radial

:DI built this cox radial a while back, it runs and idles well. 9500rpm with a 9/4 prop, idle 2200 rpm, 270 gram`s weight, 4"OD over plugs, and it is not a geared radial.

Showing results 1 to 9 of 9