RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: dskwiz
Showing results 1 to 11 of 11
Search took 0.58 seconds.
Forum: RC Car General Discussions
05-21-2008, 06:39 PM
Replies: 32
Views: 7,818
Posted By dskwiz

RE: HPI MT2 RTR

I used to have that problem. I tried the hpi wheelie bar and another aftermarket whellie bar and it still would flip over until I found this one
Wheelie bars

It will ride it all the way across...
Forum: RC Car General Discussions
05-21-2008, 05:42 PM
Replies: 32
Views: 7,818
Posted By dskwiz

RE: HPI MT2 RTR

The T3.0 has a different shaft than the G3.0 is the difference, but boy it sure makes my RTR3+ Evo scream. I have a Savage X 4.6 that runs great and will pop whellies on demand.
Forum: RC Car General Discussions
05-21-2008, 10:25 AM
Replies: 32
Views: 7,818
Posted By dskwiz

RE: HPI MT2 RTR

Keithjv,

Do you think the roto start backplate from the G3.0 will fit the OS you recommended?

Bill
Forum: RC Car General Discussions
05-21-2008, 10:23 AM
Replies: 32
Views: 7,818
Posted By dskwiz

RE: HPI MT2 RTR

It has had about 2 gallons through it. It had a bad back gasket that I have been told it was sucking air and it looks like a hair line crack in the piston. It has always had poor bottom end but the...
Forum: RC Car General Discussions
05-21-2008, 06:11 AM
Replies: 32
Views: 7,818
Posted By dskwiz

RE: HPI MT2 RTR

Keithjv,

Thanks, that does help. I had contacted OS and they recommended the same engine but said i would need a different clutch because the G3.0 I have now is a pilot shaft? and the OS has the...
Forum: RC Car General Discussions
05-20-2008, 06:19 PM
Replies: 32
Views: 7,818
Posted By dskwiz

RE: HPI MT2 RTR

Almost forgot: Which OS 18 engine do you guys recommend?

Thanks, Bill
Forum: RC Car General Discussions
05-20-2008, 06:17 PM
Replies: 32
Views: 7,818
Posted By dskwiz

RE: HPI MT2 RTR

if I want to replace my g3.0 on mt2 with an os 18 engine. Can someone give me a list of all the parts i will need to buy such as
1. do I have to buy a different clutch?
2. different spur gear?
...
Forum: Park Flyers & Backyard Flyers
09-22-2007, 02:25 PM
Replies: 2,592
Views: 227,680
Posted By dskwiz

RE: F27 STRYKER -Way Past the Limits Part 6 -Go deeper in to the Dark Side...

Is there an area here that talks about crashes perhaps caused by the AR6100 in the stryker f27C & what is the best install positions for the AR6200 in the F27C

Thanks, Bill
Forum: Park Flyers & Backyard Flyers
08-21-2007, 07:20 AM
Replies: 11,777
Views: 2,374,562
Posted By dskwiz

RE: Official Hobby Zone "Super Cub" Thread

Has anyone converted a SC to brushless? and how did you do it?
Forum: E-Flite Helicopters
06-05-2007, 11:07 AM
Replies: 8
Views: 792
Posted By dskwiz

RE: Blade CX2 - Weird occurance

Thanks, I will look into the flybar situation.
I am still concerned about the swashplate position. The mh lower head does line up it's top hole with the hole on the outer shaft, correct?

When...
Forum: E-Flite Helicopters
06-05-2007, 09:52 AM
Replies: 8
Views: 792
Posted By dskwiz

RE: Blade CX2 - Weird occurance

I bought all the microheli upgrades; upper & lower heads, upper & lower blade grips, & swash plate. I also converter to a tail boom. This thing was out of control when I flew it. You could get it up...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.