RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Whirligig
Showing results 1 to 15 of 15
Search took 0.44 seconds.
Forum: Control Lines
04-19-2020, 09:55 AM
Replies: 9
Views: 6,055
Posted By Whirligig

Uploaded the Top Flite Nobler ARF Manual

Uploaded the instruction manual for the Top Flite Nobler ARF. Good Luck!
Forum: Hitec/MultiPlex Radios- Ask Hitec Customer Service
10-16-2016, 05:23 PM
Replies: 171
Views: 128,757
Posted By Whirligig

The answer is right above your post under Aurora...

The answer is right above your post under Aurora 9 - Throttle Cut & Idle Down (http://www.rcuniverse.com/forum/fb.asp?m=9349739) Set-Up.. Throttle Cut Programming ...
Forum: Hitec/MultiPlex Radios- Ask Hitec Customer Service
01-30-2012, 12:34 PM
Replies: 2
Views: 1,160
Posted By Whirligig

RE: scan mode/function

Not me. I went into Scan Mode by accident while binding a new receiver. It was a bummer having to re-bind 7 models but at least I had the opportunity to test the lost-of-contact behavior in Scan...
Forum: Hitec/MultiPlex Radios- Ask Hitec Customer Service
06-29-2010, 01:09 AM
Replies: 9
Views: 4,006
Posted By Whirligig

RE: Trimming Out Twin Motors on an Aurora 9

Alan,

I tried both methods for twins i.e. using A9's twin engine setup and your P.Mix instruction for mixing Ch 3 & 6. The latter worked best for throttle response and motor trimming but the...
Forum: Hitec/MultiPlex Radios- Ask Hitec Customer Service
06-29-2010, 12:53 AM
Replies: 3
Views: 1,975
Posted By Whirligig

RE: Aurora 9 and Swashplate Phasing

Alan,

Finless Bob's videos on the A9 are great! Finally I understand the tradeoff between Normal and Scan mode. The Failsafe video is a must see.

Thanks,

Whirligig
Forum: Hitec/MultiPlex Radios- Ask Hitec Customer Service
06-28-2010, 11:17 AM
Replies: 3
Views: 1,975
Posted By Whirligig

RE: Aurora 9 and Swashplate Phasing

The problem has been resolved! The Airtronics 94091 servos installed by the previous owner were replaced with Hitec HS65HB and the swashplate is now in perfect phase. The replacement took serveral...
Forum: Hitec/MultiPlex Radios- Ask Hitec Customer Service
06-24-2010, 07:40 PM
Replies: 9
Views: 4,006
Posted By Whirligig

RE: Trimming Out Twin Motors on an Aurora 9

Alan,

I needed to revise the step in red from your instructions and that is to change the H: Rate and L: Rate to +100 while in the P.mixes. Without that, the rates to the program mixes are...
Forum: Hitec/MultiPlex Radios- Ask Hitec Customer Service
06-23-2010, 08:14 PM
Replies: 9
Views: 4,006
Posted By Whirligig

RE: Trimming Out Twin Motors on an Aurora 9

Alan,

Thanks for the instructions. I will give this a try using the single engine mode with a program mix to, in my case, Ch 6.

I had my first flight with the Tigercat today using the just...
Forum: Hitec/MultiPlex Radios- Ask Hitec Customer Service
06-22-2010, 08:57 PM
Replies: 9
Views: 4,006
Posted By Whirligig

Trimming Out Twin Motors on an Aurora 9

Hi,

My Aurora 9 was very easy to setup for a Fabco Tigercat parkflyer with twin electric motors. But there's a 200 to 300 rpm difference between the two motors that I'm trying to trim out. This...
Forum: Hitec/MultiPlex Radios- Ask Hitec Customer Service
05-16-2010, 12:10 PM
Replies: 4
Views: 4,459
Posted By Whirligig

RE: Linking Hitec Aurora 9 with Reflex XTR Sim

Alan,

Thanks, it worked! With the sim cable plugged to the back, I was able to see the Multi I/O menu which allowed me to select the T.pupil. After that, I started the sim and I was off and...
Forum: Hitec/MultiPlex Radios- Ask Hitec Customer Service
05-16-2010, 12:28 AM
Replies: 3
Views: 1,975
Posted By Whirligig

Aurora 9 and Swashplate Phasing

I have a problem getting rid of some swashplate phasing when pumping the collective with the Aurora 9. The helicopter is a Gazaur Poseidon 480 with a 120 degree swashplate. The elevator (Ch3) servo...
Forum: Hitec/MultiPlex Radios- Ask Hitec Customer Service
05-14-2010, 12:20 AM
Replies: 4
Views: 4,459
Posted By Whirligig

Linking Hitec Aurora 9 with Reflex XTR Sim

Hi,

I'm trying to get my Aurora 9 to work with my simulator, the Reflex XTR. I have the 1/8 inch phono jack, cable, and interface that works with my old JR 8103. I've asked MRC (Model Rectifier...
Forum: Classic RC Pattern Flying
05-26-2008, 05:47 PM
Replies: 1
Views: 718
Posted By Whirligig

RE: Banshee power plant

Found your question while researching the Banshee on this website. I'm preparing to Ebay my Banshee semi-kit that I never got around to build. With this, is my Sept. 1971 Flying Model magazine which...
Forum: Classic RC Pattern Flying
02-04-2008, 02:10 AM
Replies: 2
Views: 1,048
Posted By Whirligig

RE: BANSHEE KIT ON E-BAY. The Real Thing

I'm just wondering what a Skyglas short kit of the Banshee would be worth today. Would this model qualify for SPA? I'm about to go through my stockpile of kits I've collected over the years. There's...
Forum: Electric RC Helis
08-28-2006, 07:31 PM
Replies: 4
Views: 817
Posted By Whirligig

RE: Need Help with Optic 6 Throttle curves on Trex

I ran into the same problem yesterday with the same type of pitch curve. I had full negative pitch (-13 deg) at 0% and full positive pitch (13 deg) at 100% pitch curve. This is good for 3D but makes...
Showing results 1 to 15 of 15


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.