RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: webglider
Showing results 1 to 10 of 10
Search took 0.42 seconds.
Forum: NitroModels Support
06-28-2009, 03:49 PM
Replies: 21
Views: 3,911
Posted By webglider

RE: Extra 330 90-63

Re Striker.... PM me with your email address. I have an old electronic copy of manual I can send you.

I had elevator driven by a "dual-elevator drive" and a single carbon push rod with ball...
Forum: 3D Flying!
08-26-2008, 04:18 PM
Replies: 197
Views: 40,768
Posted By webglider

RE: Nitro Models Extra 330 90 - 63"

Now a couple of pictures of the cowl, cut for the YS110FZ and the Hatori 725 Cooling Pipe.

Others feel free to share pictures your setups ;)
Forum: 3D Flying!
08-26-2008, 04:07 PM
Replies: 197
Views: 40,768
Posted By webglider

RE: Nitro Models Extra 330 90 - 63"

Thanks for the comments, sure you would have spotted (eventually) :D

Anyway thought I would share a few of pictures of the butchery of my model.
(Please excuse the quality of the images, they...
Forum: 3D Flying!
08-25-2008, 07:14 AM
Replies: 197
Views: 40,768
Posted By webglider

RE: Nitro Models Extra 330 90 - 63"

I made a mistake with the pull pull...

Don't do what I did.... I tried to guesstimate from the outside and missed twice.... then I looked down the inside of the fuselage towards the tail from...
Forum: 3D Flying!
08-25-2008, 06:45 AM
Replies: 197
Views: 40,768
Posted By webglider

RE: Nitro Models Extra 330 90 - 63"

Here is the spec I'm planning on using...

Hitec Servos:
1x 5945MG Elevator
1x5985MG Rudder
2x5965MG Ailerons
Possibly 81/85MG for Throttle (not decided yet).

Running off a...
Forum: 3D Flying!
08-22-2008, 07:43 AM
Replies: 197
Views: 40,768
Posted By webglider

RE: Nitro Models Extra 330 90 - 63"

Depends really on your budget.... :)

My understanding is that pumped will help with the model in unusual attitudes. It will also help when you have a bit of a run of tubing between the tank and...
Forum: 3D Flying!
08-21-2008, 04:06 AM
Replies: 197
Views: 40,768
Posted By webglider

RE: Nitro Models Extra 330 90 - 63"

The holes and instructions show the option of a Dual Elevator Driver (which you have to purchase separately).
This link is to a UK site, but I'm sure that Central Hobbies or other big suppliers...
Forum: 3D Flying!
08-15-2008, 11:08 AM
Replies: 197
Views: 40,768
Posted By webglider

RE: Nitro Models Extra 330 90 - 63"

Zaboaa and Others,

I've been a bit busy with work so not had much time to do anything on the model (except to buy a few upgrade bits I want to put on it), but I was wondering what "All-up...
Forum: 3D Flying!
06-25-2008, 07:45 AM
Replies: 197
Views: 40,768
Posted By webglider

RE: Nitro Models Extra 330 90 - 63"

Hi
Very interested to come across this thread.

Recently purchased one of these models...

Just taken it out of the box, and everything looks good.

A bit of extra glue is going to be...
Forum: NitroModels Support
06-03-2008, 04:38 PM
Replies: 21
Views: 3,911
Posted By webglider

RE: Extra 330 90-63" Build & Review

Hi All,

Very interested to come across this thread.

My Extra 330 actually arrived in the post today.

Just taken it out of the box, and everything looks good.

A bit of extra glue...
Showing results 1 to 10 of 10


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.