RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Search
Today's Posts
Mark Forums Read
Vendor Directory
Notices
Search: Posts Made By: Tommie
Showing results 1 to 11 of 11
Search took 0.65 seconds.
Forum: RC Warbirds and Warplanes
12-04-2003, 07:45 PM
Replies: 818
Views: 161,276
Posted By Tommie

RE: Let's See Your Luftwaffe Birds!!!

Here are a few photos of some of the detail and I will add a quick summary of the HS 123. Justin Cork highly modified plans---Fuselage and cowl lost foam construction method---Benjamin-Moore Latex...
Forum: RC Warbirds and Warplanes
11-29-2003, 07:51 PM
Replies: 818
Views: 161,276
Posted By Tommie

RE: Let's See Your Luftwaffe Birds!!!

Great Luftwaffe photos. Here is my contribution, a Henschel HS 123A. The aircraft is in the attic at this time waiting for me to get motivated enough to rebuild it after a mishap at the Dallas...
Forum: Giant Scale Aircraft - 3D & Aerobatic
11-21-2002, 11:49 PM
Replies: 30
Views: 2,713
Posted By Tommie

Just thinking (Taurus or ZDZ)...

Aerobob
Bill sent the Stihl 50-1 oil with the Taurus and recommended it for break in. He said to run Amsol 100-1 after a two gallon break in with the 50-1. If you still have some doubts, give him a...
Forum: Giant Scale Aircraft - 3D & Aerobatic
11-15-2002, 10:25 PM
Replies: 30
Views: 2,713
Posted By Tommie

Just thinking (Taurus or ZDZ)...

I just purchased a Taurus TS 52 and mounted it on a test stand opposite my G62 so I could compare both engines. The day of the test, same fuel (Stihl 50 to 1 oil with regular gasoline), same...
Forum: Tachometer Readings
11-09-2002, 03:56 AM
Replies: 1
Views: 790
Posted By Tommie

Elevation and Engine RPM

Does anyone out there have a formula for comparing engine rpm at sea level and higher elevations? Most of the posts I have seen do not identify the elevation at which the engines are run and the rpm...
Forum: Tips & Techniques
10-01-2002, 12:40 AM
Replies: 19
Views: 2,847
Posted By Tommie

Probond Caution

Vince
The respirator I used was one from MSA Safety Works that has replaceble cartridges. I purchased it from Home Depot or Lowes. The respirator instructions also had a warning that stated "Do not...
Forum: Tips & Techniques
09-30-2002, 11:57 PM
Replies: 19
Views: 2,847
Posted By Tommie

Probond Caution

Vasek
I used Probond Polyurethane Glue for the foam sheeting. This week I had to remove some of the balsa covering for the flap well and the glue had bonded the sheet balsa to the foam as well as...
Forum: RC Scale Aircraft
09-29-2002, 10:16 PM
Replies: 5
Views: 1,361
Posted By Tommie

passing of a champion

I flew in competition with Corvin at several Scalemasters. He was always willing to help anyone with any problems they might encounter. He was an excellent craftsman and an outstanding pilot. Corvin...
Forum: Tips & Techniques
09-22-2002, 03:33 AM
Replies: 19
Views: 2,847
Posted By Tommie

Probond Caution

People who use Probond Polyurethane Glue may want to read and heed the warnings on the label. "Warning: Exposure may result in acute or delayed damage to the lungs. Eye irritant. May irritate or...
Forum: Gas Engines
08-16-2002, 09:50 PM
Replies: 38
Views: 4,636
Posted By Tommie

Bent Shaft!!!

I probably should have used a term like"wobble factor" rather than run out. Before I sent the G62 to Ralph, I ran the engine and looking from the side of the engine at the 22-10 Zinger, I noticed...
Forum: Gas Engines
08-08-2002, 02:49 AM
Replies: 38
Views: 4,636
Posted By Tommie

Bent Shaft!!!

Bent Crankshaft
I just had Ralph straighten a G62 shaft for me. There is now no run out at full throttle. He did an outstanding job at a reasonable price.
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.