RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Community
Search
Notices
Search: Posts Made By: morati
Showing results 1 to 12 of 12
Search took 0.41 seconds.
08-24-2008, 06:10 PM
Replies: 2,034
Views: 128,095
Posted By morati

RE: OFFICIAL Detta ST THREAD **********

I'm in the same boat as you. I finally fried my 33a Pro Car ESC and since they no longer make it, I just bought a 65a Roadster from Ebay for $75. Should match up with my new Neu motor well.
I was...
08-16-2008, 01:25 PM
Replies: 13
Views: 1,913
Posted By morati

RE: Exotek Vendetta/Vendetta ST Chassis

Its stiff enough for offroad on dirt but I wouldn't mind it a little stiffer and lighter for carpet.....
08-15-2008, 09:08 PM
Replies: 13
Views: 1,913
Posted By morati

RE: Exotek Vendetta/Vendetta ST Chassis

Why saddle-packs? I own a KM-RC Mini Inferno that uses these and they are a PITA! Its very difficult to find high quality lipos in this small size. Its one of the reasons I didn't buy an EXOTEK...
08-03-2008, 08:01 PM
Replies: 8
Views: 786
Posted By morati

RE: Need foam tires for Vendetta ST

www.geckotyres.com
Get these in 1/10th front electric 37 shore and true them down to 58mm. These are the best I have ever used......Gotta order them from the UK though.
07-30-2008, 12:54 PM
Replies: 2
Views: 490
Posted By morati

RE: parallel wiring

Yes, I do this to my lipo's because I run a saddle pack configuration. Wire + to + and - to - on my two 7.4v or 11.1v packs onto the Deans (or connector of your choice) and you're good to go.
07-28-2008, 08:44 AM
Replies: 2,034
Views: 128,095
Posted By morati

RE: OFFICIAL Detta ST THREAD **********

The Vendetta does indeed use mod .6 pinions which I believe is also termed as 48p Metric?
AE RC18T, Kyosho Mini Inferno, Losi Mini-T all use 48p mod. 5 pinions
Xray M18 series uses standard 48p...
07-27-2008, 04:34 PM
Replies: 2,034
Views: 128,095
Posted By morati

RE: OFFICIAL Detta ST THREAD **********

So this is where you guys are hiding, LOL! I miss one18th......
Thanks Metallover and rschoi_75 for the suggestions. The Mongoose has taken up permanent residence in my LRP Shark FT and I am...
07-26-2008, 06:41 PM
Replies: 2,034
Views: 128,095
Posted By morati

RE: OFFICIAL Detta ST THREAD **********

Actually, I'm using the new Novak Mongoose system. 48p is not the same as mod .6 causing alot of noise. Novak makes some for their system to be used with the Vendetta but the 11t ones have been...
07-26-2008, 04:02 PM
Replies: 2,034
Views: 128,095
Posted By morati

RE: OFFICIAL Detta ST THREAD **********

Does anyone know if someone makes a .6mod pinion in 10t or 11t for a 1/8th shaft motor?
Forum: RC Truggy
04-16-2007, 11:39 PM
Replies: 874
Views: 131,544
Posted By morati

RE: Offical Mugen MBX5T thread

Any thoughts on this one fellas? Worth it or not?
http://cgi.ebay.com/ws/eBayISAPI.dll?ViewItem&ih=002&sspagename=STRK%3AMEWA%3AIT&viewitem=&item=120108161034&rd=1&rd=1
04-14-2007, 01:20 PM
Replies: 1,320
Views: 112,812
Posted By morati

RE: :: Official MBX5/Prospec Thread !!

Thanks for the reply. Yeah, I figured there was no sense buying something that I would end up reselling after a month and then have to buy the Mugen as well. May as well save the money and buy the...
04-13-2007, 11:24 PM
Replies: 1,320
Views: 112,812
Posted By morati

RE: :: Official MBX5/Prospec Thread !!

Gentlemen, I have been racing electrics for the last 5 years or so and would like to make the jump to Nitro. I have read literally hundreds of pages of posts both here and on other forums before...
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.