RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 10
1
2
3
Last »
Search: Posts Made By: john flynn
Showing results 1 to 25 of 227
Search took 1.41 seconds.
Forum: Gas Engines
03-12-2010, 06:57 AM
Replies: 19
Views: 4,886
Posted By john flynn

RE: Saito FG36

Going to try a few more things before I get one but the CH unit sounds like the right choice. This method of tuning reads interesting regardless of the emphasis on 2 stroke engines and not like...
Forum: Gas Engines
03-12-2010, 03:52 AM
Replies: 19
Views: 4,886
Posted By john flynn

RE: Saito FG36

W8ye, I just measured the Saito's senders position campared to the required 28 degree BTDC for CH and the DL ignitions. It read 17 degrees ATDC is this right?
Forum: Gas Engines
03-12-2010, 03:26 AM
Replies: 19
Views: 4,886
Posted By john flynn

RE: Saito FG36

G'day Kim, 150 mls to 3 lts of premium fuel is the blend I'm using, 20 to 1. If I were to richen the high speed half a turn, I'd lose about 1000 revs. I reckon over the last 3 days there's not a...
Forum: Gas Engines
03-11-2010, 06:17 PM
Replies: 19
Views: 4,886
Posted By john flynn

RE: Saito FG36

Yep followed tuning instructions to the letter. I'm not one to give up but man I've had my fill of this engine. I took advantage of a higher Aussie dollar and purchased the engine from the US. I...
Forum: Gas Engines
03-11-2010, 06:07 AM
Replies: 19
Views: 4,886
Posted By john flynn

RE: Saito FG36

By earthing the plug out, I can get a good spark just by hand rocking. Gap needed widening a touch to .65mm. I advanced the sender unit by rotating clockwise on it's sloted holes. As an outcome...
Forum: Gas Engines
03-10-2010, 06:11 PM
Replies: 19
Views: 4,886
Posted By john flynn

RE: Saito FG36

Thanks, w8ye, I'm confident the fuel set up is all ok so that leaves the electrics. I've sent for a new plug for starters, any ideas on ignition testing DIY ? Thanks again.
Forum: Gas Engines
03-10-2010, 03:22 AM
Replies: 19
Views: 4,886
Posted By john flynn

Saito FG36

G'day all, I'm having problems with the above engine. I have it mounted semi inverted in a 100" Big Stik using a 6 volt 2200 mha Battery for ignition. 20/1 fuel mix, oil is Motul 2t 100% synthetic...
Forum: Questions and Answers
12-16-2009, 06:23 PM
Replies: 0
Views: 539
Posted By john flynn

100" Big Stik Saito FG36

G'day all, I'm building a 100" Big Stik off a Don Anderson/Mike Smith Plan. I'm in the process of fitting a Saito FG36 to it. Is there a way of disconnecting the high tension wire from the plug...
Forum: Questions and Answers
09-13-2009, 05:58 PM
Replies: 2
Views: 793
Posted By john flynn

RE: 100 inch Big Stik

Thanks for the info Harley. I'm tempted to get a Saito FG36, that should be OK for the job aye? The 8411 you mentioned have 15 kg of pull, is'nt that a bit of over kill? Regards, John.
Forum: Questions and Answers
09-10-2009, 09:30 PM
Replies: 2
Views: 793
Posted By john flynn

100 inch Big Stik

G'day all, i've just recieved a short kit of a 100 inch Big Stik and would like some suggestions on servo sizes (JR prefered) for the control surfaces. Would also like suggestions on what size...
Forum: Forum questions or problems
09-19-2006, 12:08 AM
Replies: 0
Views: 406
Posted By john flynn

r/c universe videos

Hi, is there any way to download the clips and watch them on another player? The one that plays them is a bit small to make out much detail[8D] Regards, John.
Forum: Questions and Answers
11-10-2005, 07:24 AM
Replies: 16
Views: 4,551
Posted By john flynn

RE: cm pro katana 50

Yes mate, he's had enough of it. John.
Forum: Questions and Answers
11-10-2005, 04:20 AM
Replies: 16
Views: 4,551
Posted By john flynn

RE: cm pro katana 50

Please disregard all my former post's on this plane as it is, no more. After making some more alterations to sort out the probs my friend put her in pretty hard. He will now hang it from the...
Forum: Questions and Answers
11-07-2005, 02:46 PM
Replies: 16
Views: 4,551
Posted By john flynn

RE: cm pro katana 50

If I was to put a pull pull set up I would do away with the twin elevator servos and just use 1. This would drive a bell crank with wires to the elevator halves. Good luck with the plane and I...
Forum: Questions and Answers
11-06-2005, 09:26 PM
Replies: 16
Views: 4,551
Posted By john flynn

RE: cm pro katana 50

I'll be interested to know if you have the same probs with it, please keep me posted. Regards, John.
Forum: Questions and Answers
11-06-2005, 05:52 PM
Replies: 16
Views: 4,551
Posted By john flynn

RE: cm pro katana 50

Having the servos in the horizontal position spreads the load over the their entire length. Positioned vertically the load is forced against their width which allows alot of flex. The Saito 72 has...
Forum: Questions and Answers
11-06-2005, 04:23 AM
Replies: 16
Views: 4,551
Posted By john flynn

RE: cm pro katana 50

one more showing those quick link thingamajigs.
Forum: Questions and Answers
11-06-2005, 04:14 AM
Replies: 16
Views: 4,551
Posted By john flynn

RE: cm pro katana 50

here is a few pics of the elevator setup, not real pretty.
Forum: Questions and Answers
11-06-2005, 04:06 AM
Replies: 16
Views: 4,551
Posted By john flynn

RE: cm pro katana 50

My mate went ahead and installed 2 servos down the tail. He used JR 539's which I think is a bit of overkill, but was all he had. He installed them vertically instead of horizontally and there is...
Forum: Questions and Answers
11-03-2005, 04:39 AM
Replies: 16
Views: 4,551
Posted By john flynn

cm pro katana 50

G'day all, a fellow club member has the above plane and when he attempt's a loop it rolls out to the extreme. I checked the elevator pushrods and they have alot of flex in them. Would going to...
Forum: Kit Building
10-30-2005, 08:31 AM
Replies: 529
Views: 150,287
Posted By john flynn

RE: [b]Flight Report!!![/b]

Nice graphics flynoz, your flying site looks good too. No drought on there by the green scene. Hey firstofficer, you where in the right state but to far south. North Queensland is where God...
Forum: Kit Building
10-30-2005, 08:20 AM
Replies: 529
Views: 150,287
Posted By john flynn

RE: [b]Flight Report!!![/b]

nah mate, have another go, John.
Forum: Kit Building
10-30-2005, 08:17 AM
Replies: 529
Views: 150,287
Posted By john flynn

RE: [b]Flight Report!!![/b]

G'day flynoz, try the post reply instead of the fast reply and you should see the upload link. Welcome to r/c universe. Regards, John.
Forum: Crash & Rebuild
10-14-2005, 12:04 AM
Replies: 160
Views: 57,313
Posted By john flynn

RE: Jet crash video

Found it http://www.hobbyclub.ru/videoeng.html
Forum: Crash & Rebuild
10-13-2005, 11:59 PM
Replies: 160
Views: 57,313
Posted By john flynn

RE: Jet crash video

G'day to all, can anyone speak Russian? I can't and am having dificulty in finding the link to the jet crashs. Please help. Regards, John.
Showing results 1 to 25 of 227
 
Page 1 of 10
1
2
3
Last »


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.