RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 2
1
2
Search: Posts Made By: WwpIII
Showing results 1 to 25 of 42
Search took 0.68 seconds.
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
12-17-2002, 05:06 PM
Replies: 0
Views: 467
Posted By WwpIII

Duralites

i am trying to find out a little more about these batteries...here's my deal i am putting together my flip 3D with 5 JR811's 2 on the elevator and the extra for rudder pull-pull and want to save...
Forum: 3D Flying!
12-17-2002, 04:55 PM
Replies: 220
Views: 27,929
Posted By WwpIII

Carbon Fiber

hey tony....nice pics

i hope i can get that control throw with my aluminum arms...they are not the 3-D like you used but they are the large.....did you you reinforce those MK horns with a...
Forum: 3D Flying!
12-14-2002, 05:46 PM
Replies: 16
Views: 1,782
Posted By WwpIII

MK horns

so did you drill and insert a dowel for these horns i have the same ones both small and medium size and am planning on using them...my plan was to insert a 3/8's dowel in each surface to reinforce...
Forum: 3D Flying!
12-13-2002, 02:20 PM
Replies: 16
Views: 1,782
Posted By WwpIII

elevators torque rod

so tony how did the elvevator torque rod work for you...are you getting much flex between the two halfs using it...i finally have received all my orders from various places....going with the rudder...
Forum: Profile and Fun Flying Planes
12-04-2002, 07:17 PM
Replies: 0
Views: 460
Posted By WwpIII

Flip 3D (covering)

does anyone know what brand of covering is on this airplane?

i have a whole roll of clear monokote...and if i can get the heat necessary to apply it i will use it to seal my hinge lines...
Forum: ARF or RTF
12-04-2002, 07:04 PM
Replies: 1
Views: 534
Posted By WwpIII

Flip 3D "covering"

does anyone know for sure what brand of covering is on this plane? it seems to be of good quality, but i can't find out what brand it is...i have some clear monokote that i want to use for sealing...
Forum: Profile and Fun Flying Planes
12-03-2002, 05:40 PM
Replies: 32
Views: 2,551
Posted By WwpIII

what a nice site.......

this site rocks...i have been posting concerns here for about 3 weeks now...and after searching back over 11 months i found some issues on pull pull....still i haven't found all my answers...i...
Forum: 3D Flying!
12-03-2002, 05:14 PM
Replies: 11
Views: 1,107
Posted By WwpIII

Pull Pull cables exposed???

i have never used the wheels....but i can see an advantage as far as the geometry goes on the servo end..it stays the same....and if you connect on the hinge line on the control surface that is the...
Forum: 3D Flying!
12-03-2002, 05:08 PM
Replies: 16
Views: 1,782
Posted By WwpIII

Flip 3D (build/set-up tips)

i have no way of getting a precise weight measurement...looking for somebody who makes nice scales for these rc planes....i am still awaiting part's ordered for this plane so until i have them i...
Forum: 3D Flying!
12-03-2002, 03:19 PM
Replies: 11
Views: 1,107
Posted By WwpIII

Pull Pull cables exposed???

well first of all thanks for all the input on this....i am sure i will go with this plan....now i just need to look for a arm or wheel for the servo....i have already ordered the aluminum control...
Forum: 3D Flying!
12-03-2002, 02:54 PM
Replies: 16
Views: 1,782
Posted By WwpIII

carbon fiber

are you using the rods or the strips....i have heard of reinforcing with the strips during building prior to covering, but have not seen it done before...how would you attach it and make it look...
Forum: 3D Flying!
12-02-2002, 06:08 PM
Replies: 11
Views: 1,107
Posted By WwpIII

Pull Pull cables exposed???

thanks for that info.....the only problem i figured i would have would be flutter from the cable....i have used pull pull systems several times but i have never had near this much of the cable...
Forum: 3D Flying!
12-02-2002, 05:57 PM
Replies: 21
Views: 1,418
Posted By WwpIII

Servo resolution with 3D rates?

in what way are you putting in "1 step" to see this difference.....if it is using the trim tabs on the transmitter then depending on which transmitter you are using it could be up to 6-10 steps per...
Forum: 3D Flying!
12-02-2002, 05:01 PM
Replies: 11
Views: 1,107
Posted By WwpIII

Pull Pull cables exposed???

hello all....need some input please....

i have posted this question already in another previous thread, but perhaps it's not getting noticed...i am in the process of assembling the flip 3D...
Forum: 3D Flying!
12-02-2002, 03:50 PM
Replies: 22
Views: 1,488
Posted By WwpIII

going with the 72(and pull-pull)

i feel this will be a good combo...because i already have the engine is the main reason...i have had this plane on the building table now for over a week...not one drop of glue yet.....i have been...
Forum: 3D Flying!
11-30-2002, 12:21 AM
Replies: 22
Views: 1,488
Posted By WwpIII

Saito 100 in Kyosha Flip 3D?

i have the plane on the bench...no glue yet..going with the saito 72, since i already have it....it does say more than once in the manual too not overpower this plane..and more than once does it say...
Forum: Glow Engines
11-30-2002, 12:05 AM
Replies: 7
Views: 760
Posted By WwpIII

Four strokes and nitro

i fly os and saito 4strokes and i did try some 30% morgan heli fuel in the saito at the end of the flying season this year....only a few flights, but what a difference it made.... it was...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
11-27-2002, 06:19 PM
Replies: 0
Views: 340
Posted By WwpIII

DS811's

anyone have input on these servos...i just ordered 6 of them from a friend that has a lhs....he is letting me buy them for $35 a piece..dealer cost's i presume...i am planning on putting them on my...
Forum: 3D Flying!
11-27-2002, 06:06 PM
Replies: 1
Views: 594
Posted By WwpIII

Anyone Flying The Flip Yet!!!!!!!

i have one laid out on the building table, have had it there for about a week...still haven't put any glue on it.......there are some changes that i feel are needed according to the construction...
Forum: 3D Flying!
11-27-2002, 06:00 PM
Replies: 6
Views: 659
Posted By WwpIII

flying wires on the flip3D

tower hobbies sells this plane...towerhobbies.com ..but the best pics were posted here on this site of the plane prebuilt.....kyosho.com has a nice pic of in-flight...i do not see the flying wires on...
Forum: Glow Engines
11-27-2002, 03:34 PM
Replies: 11
Views: 1,065
Posted By WwpIII

Why not invert?

i thought the fuel issue could be the reason...but i see no problems with inverting...if anyone is running a 4 stroke and not using the OS F plug...well you are missing out...i am going with the...
Forum: Glow Engines
11-27-2002, 02:51 PM
Replies: 11
Views: 1,065
Posted By WwpIII

Why not invert?

any ideas on why the flip3d manual is having you mount the 4 strokes at 90 degrees and the 2 strokes inverted...i am going with the saito 72 on this plane and am planning on inverting it...
Forum: 3D Flying!
11-22-2002, 07:40 PM
Replies: 11
Views: 943
Posted By WwpIII

Where can I buy a bellcrank for my H9 Sukhoi rudder

as already told...nelson hobby rocks....top of the line....
Forum: 3D Flying!
11-22-2002, 07:39 PM
Replies: 0
Views: 417
Posted By WwpIII

Another Flip Thread

I wish we had more input on the other threads concerning the flip...very nice plane...but not much info coming through...anyone interested in this plane should check out the older threads...after...
Forum: 3D Flying!
11-22-2002, 02:22 PM
Replies: 10
Views: 1,360
Posted By WwpIII

Flip 3D (nice pics tipstall)

what do you think about the flying wires...not sure if they are needed or not.....i have looked at everything pretty good...and i am considering using the rear servo mounts to work the elevators...
Showing results 1 to 25 of 42
 
Page 1 of 2
1
2


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.