RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: roscoerc
Showing results 1 to 14 of 14
Search took 0.29 seconds.
Forum: ARF or RTF
03-11-2017, 10:20 AM
Replies: 4
Views: 1,083
Posted By roscoerc

Duncan, thanks for the info. that's right about...

Duncan, thanks for the info. that's right about where I was going to start. did you use the CG that the manual gives? about 3 3/4 from the LE? I'm using a DLE 20, and with both batteries wedged...
Forum: ARF or RTF
03-08-2017, 05:23 PM
Replies: 4
Views: 1,083
Posted By roscoerc

phoenix supercub control throws

assembling a 90" supercub the manual lists throws for elevator and aileron as 8mm on low rate and 10mm on high the elevator thickness is about 3/8", which would give it very little travel. maybe...
Forum: Glow Engines
10-31-2016, 02:59 PM
Replies: 4
Views: 766
Posted By roscoerc

loose needle valve on Magnum 91 4st

magnum 91 4 stroke w/ approx 1/2 gallon through it (wildcat 10%) runs great with the needle open about 11/3 to 11/4 turns out I thought that would be a real lean setting, but it's only 170-180 at...
Forum: Gas Engines
03-22-2015, 11:02 AM
Replies: 8
Views: 7,138
Posted By roscoerc

thanks for the input guys I have plenty of room...

thanks for the input guys I have plenty of room in the cabin area to put up to a 16 oz tank and it would be closer to the CG it would be about 11" from the tank to the carb would the engine draw...
Forum: Gas Engines
03-22-2015, 03:44 AM
Replies: 8
Views: 7,138
Posted By roscoerc

DLE 20 fuel consumption

I'm installing a DLE 20 in a Champ with a small tank compartment. I could cram a 12 oz tank in, but it would be a tight fit. A 10 oz tank fits perfect. What kind of run time can I expect? Other than...
Forum: Gas Engines
01-15-2015, 03:16 PM
Replies: 7
Views: 6,494
Posted By roscoerc

wish the DLE 20RA manual wouldn't list the dubro...

wish the DLE 20RA manual wouldn't list the dubro mount as acceptable. I got the engine and mount from Tower last month. needless to say, it doesn't fit. I ended up getting some 1/2 " aluminum square...
Forum: RC Flight Simulator Software
01-14-2015, 04:16 PM
Replies: 1
Views: 1,224
Posted By roscoerc

RF 7.5 upgrade

I'm currently runnng a RF 6.5 upgrade that was installed over the full RF 5 program. Will the 7.5 upgrade install over the 6.5? Is there anything I need to watch out for on the install? thanks for...
Forum: Batteries & Chargers
01-14-2015, 03:37 PM
Replies: 2
Views: 699
Posted By roscoerc

need a new charger

I've been running a triton2 for about 5 years and it finally gave up. I need advice on a new charger, nothing too fancy or complicated. I run mainly nimh for recievers, nicads in the radio, and a...
Forum: Gas Engines
12-09-2014, 12:09 AM
Replies: 17
Views: 2,292
Posted By roscoerc

thanks for the input guys. based on weight...

thanks for the input guys. based on weight issues, I'll probably go with a DLE 30. can I assume that these will run inverted a lot better than a glow engine?
Forum: Gas Engines
12-06-2014, 10:04 PM
Replies: 17
Views: 2,292
Posted By roscoerc

20cc engine choices

I'm looking to replace a ST 2000 in a Bud Nosen champ. I finally got tired of fooling with the carb to get a good run. I'm looking at the DLE 20, or Zenoah 20 as a replacement. This will be my first...
Forum: Futaba Radios Direct support forum
08-14-2013, 03:39 PM
Replies: 0
Views: 352
Posted By roscoerc

6004FF reciever won't link

I have a 9C radio with a TM 8 module. 6008 and 617 recievers linked up with no problem. Plugged in a brand new 6004, hit the link button and only get a blinking green light, with no servo movement....
Forum: Kit Building
09-20-2010, 06:58 PM
Replies: 1
Views: 539
Posted By roscoerc

Bud Nosen (A&A Ind.) Champ wing mounting

Has anyone built a Champ using the wing mounting shown on the plans; drilling THROUGH the wing dowels & center section tube, bolting to blind nuts mounted in the cabin rail? Seems like a big loss of...
Forum: ARF or RTF
05-15-2010, 06:14 PM
Replies: 3
Views: 952
Posted By roscoerc

Kadet LT 40 cg

I just acquired an LT 40 in a trade; needs some work and an engine. Anyone have any plans or instructions concerning the CG range? I think it was originally an ARF. Thanks for any help. Dave
Forum: SuperTigre Engines Support
12-25-2009, 08:11 PM
Replies: 5
Views: 1,493
Posted By roscoerc

ST 2000 SETTINGS

i have an Italian st2000 in good shape. What type of fuel, prop, glowplugs, and initial needlevalve settings do I need to be concerned with before I start to benchrun it? Thanks for any help. Dave
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.