RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 4
1
2
3
Last »
Search: Posts Made By: shane55
Showing results 1 to 25 of 81
Search took 0.28 seconds.
Forum: Gas Engines
03-19-2023, 02:53 PM
Replies: 8
Views: 933
Posted By shane55

Can the roller pin bearing on the crankshaft be...

Can the roller pin bearing on the crankshaft be replaced or does it come fixed to the crankshaft as it appears to be here...
Forum: Gas Engines
03-19-2023, 02:14 PM
Replies: 8
Views: 933
Posted By shane55

Not on Dle's but I've had those roller pin...

Not on Dle's but I've had those roller pin bearing fail on crrc engines in the past. The engine is coming up on 50hrs running so I suppose I should change them out anyway. They can make an awful mess...
Forum: Gas Engines
03-19-2023, 08:46 AM
Replies: 8
Views: 933
Posted By shane55

Thanks but shipping and customs to Ireland from...

Thanks but shipping and customs to Ireland from the US usually makes things prohibitively expensive thats why I was curious about the bearings on alixpress.
Forum: Gas Engines
03-18-2023, 03:04 PM
Replies: 8
Views: 933
Posted By shane55

Dle 20 crankshaft bearings

I have a Dle 20 which runs well but the sound when idling has got a bit noisier, presume the crankshaft bearings are wearing. I notice the same size bearings are available on alixpress for a fraction...
Forum: Gas Engines
04-10-2017, 04:18 AM
Replies: 23
Views: 3,480
Posted By shane55

Yes, time to abandon the gp26r I think, wont be...

Yes, time to abandon the gp26r I think, wont be buying anymore CRRC !
Forum: Gas Engines
04-09-2017, 03:49 PM
Replies: 23
Views: 3,480
Posted By shane55

Lets say the crankshaft, conrod and bearing are...

Lets say the crankshaft, conrod and bearing are replaced whats to stop the bearing shifting back slightly and wearing off the backplate again? What I cant understand is why there is apparently...
Forum: Gas Engines
04-09-2017, 03:02 PM
Replies: 23
Views: 3,480
Posted By shane55

So I rebuilt the engine and have flown it for...

So I rebuilt the engine and have flown it for about 10hrs until the big end bearing failed again last friday. Damage was not as bad as last time, just the piston and ring.The problem seems to be that...
Forum: Gas Engines
11-16-2015, 03:26 AM
Replies: 6,892
Views: 1,138,402
Posted By shane55

I had something like that with a crrc 26 a few...

I had something like that with a crrc 26 a few yrs ago. I was running it on the ground when it stopped suddenly. after that it could not be turned over past just before TDC. I opened it up and found...
Forum: ARF or RTF
12-29-2014, 02:29 PM
Replies: 2,530
Views: 399,355
Posted By shane55

duplicate post, removed

duplicate post, removed
Forum: ARF or RTF
12-29-2014, 02:29 PM
Replies: 2,530
Views: 399,355
Posted By shane55

So they are practically the same size regards...

So they are practically the same size regards fuselage length and wingspan. There is a big difference in weight though. The highest specified weight for the 60 size was 8.5lb whereas its 13.5lbs for...
Forum: ARF or RTF
12-29-2014, 04:44 AM
Replies: 2,530
Views: 399,355
Posted By shane55

I would imagine that sort of conversion would be...

I would imagine that sort of conversion would be alot more trouble than its worth. Probably make alot more sense just to get the whole new H9 model.They probably charge at least half the price of the...
Forum: Gas Engines
12-04-2014, 10:20 AM
Replies: 23
Views: 3,480
Posted By shane55

Whoops! Did I? I removed very little, only...

Whoops! Did I? I removed very little, only polished it really
Forum: Gas Engines
12-04-2014, 08:49 AM
Replies: 23
Views: 3,480
Posted By shane55

There is some scratching on the backplate. I had...

There is some scratching on the backplate. I had to replace the crankcase after the bearing failure as the conrod cracked it. There is about 2mm clearance between the crankshaft and backplate.
...
Forum: Gas Engines
12-03-2014, 08:03 AM
Replies: 23
Views: 3,480
Posted By shane55

GP26R big end bearing wearing off crankshaft?

I am replacing the big end bearing in my GP26r after it failed after only 6 hrs running. After comparing the new bearing with the old one it looks like the old one wore out due to contact with the...
Forum: Gas Engines
11-20-2014, 02:13 PM
Replies: 8
Views: 762
Posted By shane55

I tried that, didnt seem to want to budge

I tried that, didnt seem to want to budge
Forum: Gas Engines
11-20-2014, 07:37 AM
Replies: 8
Views: 762
Posted By shane55

Crrc gp26r Crankshaft bearing removal

I've tried heating the crankcase in the Oven but it didn't work. How are the bearings removed ?
Thanks
Forum: Gas Engines
09-13-2014, 05:25 AM
Replies: 9
Views: 750
Posted By shane55

Thanks, tried a different plug and its running...

Thanks, tried a different plug and its running fine.its another Chinese plug, I don't have anything else.I have not had a problem with the Chinese plugs before although I know alot of people do.I'll...
Forum: Gas Engines
09-12-2014, 11:28 AM
Replies: 9
Views: 750
Posted By shane55

I replaced the piston ring, ran it on the ground...

I replaced the piston ring, ran it on the ground for 3 hrs and it seemed fine.Then it started getting harder to start, first it would fire but would not stay running unless it was started at about...
Forum: ARF or RTF
08-16-2014, 03:22 AM
Replies: 33
Views: 9,979
Posted By shane55

I used a DLE 20, plenty of power but the...

I used a DLE 20, plenty of power but the biggest/heaviest engine that could be fitted. There is no way it would take a 26cc, doesn't need it anyway. I've never heard of using power for spin recovery....
Forum: ARF or RTF
08-14-2014, 02:29 AM
Replies: 33
Views: 9,979
Posted By shane55

Sorry to hear about your mishap, I have spun it a...

Sorry to hear about your mishap, I have spun it a few times, spin is steep probably because mine is a bit nose heavy, steep spin is preferable to flat though as far as recovery is concerned
Forum: Gas Engines
05-02-2014, 03:28 AM
Replies: 26
Views: 2,742
Posted By shane55

I replaced the #4 module on my first dle20 with a...

I replaced the #4 module on my first dle20 with a standard rcexl module and its working fine. I have lately got a 2nd dle20 that came with the #4 A-02 module thats going into a seagull C152. The...
Forum: Gas Engines
05-02-2014, 02:32 AM
Replies: 26
Views: 2,742
Posted By shane55

I have 2 versions of the #4 module, A-01 and...

I have 2 versions of the #4 module, A-01 and A-02. The A-02 has a higher working voltage, 8.4V as opposed to 6V with the A-01. I have not used the A-02 yet but I think I read that the only difference...
Forum: Gas Engines
05-01-2014, 01:58 PM
Replies: 26
Views: 2,742
Posted By shane55

Which module is that, I have the A-01 and A-02,...

Which module is that, I have the A-01 and A-02, Is it called A-03 ??
Forum: Gas Engines
04-30-2014, 02:40 PM
Replies: 26
Views: 2,742
Posted By shane55

I could repair it for about €50, It cost €140,...

I could repair it for about €50, It cost €140, haven't decided yet if I will repair it. On the GF26i the crank, bearing and con are press fitted together, they are separate parts on the gp26r athough...
Forum: Gas Engines
04-30-2014, 01:05 PM
Replies: 26
Views: 2,742
Posted By shane55

I hadnt thought of doing that, using bearings...

I hadnt thought of doing that, using bearings from a different source, I thought the sizes/tolerances might be out if you didnt get the oem. But I presume they are standard sizes, are they? CRRC only...
Showing results 1 to 25 of 81
 
Page 1 of 4
1
2
3
Last »


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.