RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: bcr1953chevy
Showing results 1 to 25 of 45
Search took 0.22 seconds.
02-08-2010, 04:35 PM
Replies: 28
Views: 10,993
Posted By bcr1953chevy

RE: Blade MSR Main Rotor Grips - Washers and O-Rings

When I installed the O rings, I accidently ended up with 2 sets and YES, it was very tight.

When you have the MSR rotor apart, examine the main rotor head. You will probably notice that the O...
02-01-2010, 06:24 PM
Replies: 17
Views: 9,178
Posted By bcr1953chevy

RE: Best Beginner Heli Kit Under $100??

The smaller heli's don't fly very well outside. I have a Blade MSR (fixed pitch) that I fly indoors in a space that is about 12 ft by 14 ft. It takes a little patience and I do encounter a few...
02-01-2010, 06:17 PM
Replies: 14
Views: 1,555
Posted By bcr1953chevy

RE: RC Helis....dont buy'em

Blade makes several good products for beginning hobbyists. I used to fly planes. I'm rather new to the heli sport. Purchased a Blade MSR that I've been flying in my living room for about six weeks....
02-01-2010, 05:49 PM
Replies: 28
Views: 10,993
Posted By bcr1953chevy

RE: Blade MSR Main Rotor Grips - Washers and O-Rings

There is another thread, "MSR - is the DX6I worth buying" that discusses flying the MSR with the larger transmitters.
01-25-2010, 08:06 PM
Replies: 9
Views: 2,518
Posted By bcr1953chevy

RE: MSR Upgrades?

I have used the 150 mah battery on my MSR. I did not notice any handling problems. The 120 mah batteries don't last very long. The 150 mah batteries do add a little flight time.
01-24-2010, 08:49 PM
Replies: 28
Views: 10,993
Posted By bcr1953chevy

RE: Blade MSR Main Rotor Grips - Washers and O-Rings

Some good tips on the throttle. I agree, get it off the ground a little and it settles down.

Since I removed the extra O rings, mine flies as it did out of the box.

For those of you who are...
01-23-2010, 06:09 AM
Replies: 28
Views: 10,993
Posted By bcr1953chevy

RE: Blade MSR Main Rotor Grips - Washers and O-Rings

Sorry that I've not responded before. I did not have time to work on the MSR this week. Work's been interfering with my hobby... This morning I found the answer to the problem! I read the last few...
01-18-2010, 04:01 PM
Replies: 28
Views: 10,993
Posted By bcr1953chevy

RE: Blade MSR Main Rotor Grips - Washers and O-Rings

Lipps199,

Can you tell me if the rubber Orings and washers are installed on your "factory" MSR?
01-17-2010, 09:33 PM
Replies: 9
Views: 2,518
Posted By bcr1953chevy

RE: MSR Upgrades?

Just curious, are the rubber O rings and washers installed on the fethering spindle between the main rotor hub and the blade grips? Ireplaced my blade grips, installed the rubber O rings and washers...
01-17-2010, 09:27 PM
Replies: 40
Views: 12,602
Posted By bcr1953chevy

RE: Help with flimsy/breakable Blade mSR struts

I found that it takes a lot more throttle to get it off the ground. It used to lift and climb just below 1/2 throttle. Now I have to get above 1/2 throttle for it to lift at all. My gear does not hit...
01-17-2010, 09:16 PM
Replies: 28
Views: 10,993
Posted By bcr1953chevy

RE: Blade MSR Main Rotor Grips - Washers and O-Rings

to ct420 - Iuse the orange swashplate adjustment tool every time I have a hard landing or crash. Once or twice the swash plate bearing was loose and I was able to repair it. I don't believe that is...
01-16-2010, 06:41 PM
Replies: 28
Views: 10,993
Posted By bcr1953chevy

RE: Blade MSR Main Rotor Grips - Washers and O-Rings

Ifound a linkage problem with the flybar. Ireplaced the flybar and one of the linkages. It helped but it still flys like a crazy bird.

When operating the aileron and elevator servo, should the...
01-16-2010, 01:44 PM
Replies: 28
Views: 10,993
Posted By bcr1953chevy

RE: Blade MSR Main Rotor Grips - Washers and O-Rings

Now I've done it. I turned my easily able to hover MSR into a flying crazy bird. It takes off and angles back and to the side. Adjusting the trim settings does not seem to have an affect.

I should...
01-16-2010, 01:38 PM
Replies: 40
Views: 12,602
Posted By bcr1953chevy

RE: Help with flimsy/breakable Blade mSR struts

Itoo had to drill the fiberglass to get the nylon screw to fit through it. I also had to drill the frame of the MSRwith a 5/64" bit to get the screws to thread into it. The original holes are not...
01-16-2010, 06:27 AM
Replies: 4
Views: 644
Posted By bcr1953chevy

Source for Screws and Other Hardware

Does anyone know a good source for screws, washers, O rings, etc. At the rate at which Ican lose these things, buying several in a pack is not economical.

Itried my usual sources, Fastenal and the...
01-16-2010, 05:52 AM
Replies: 40
Views: 12,602
Posted By bcr1953chevy

RE: Help with flimsy/breakable Blade mSR struts

I installed the epoxy repaired gear last evening. The front pin broke off after the second flight. The aluminum pin shown in a previous post is probably the better repair.

Iordered the fiberglass...
01-16-2010, 05:31 AM
Replies: 28
Views: 10,993
Posted By bcr1953chevy

RE: Blade MSR Main Rotor Grips - Washers and O-Rings

I contacted Horizon Hobby yesterday by telephone and they advised that yes, those washers and O rings belong between the grips. I mentioned that it makes the assembly pretty tight but they did not...
01-14-2010, 10:09 PM
Replies: 21
Views: 7,312
Posted By bcr1953chevy

RE: My first heli, E-flite Blade MSR! Questions.....

Just saw this thread. I asked a question about the Blade MSR main rotor grips but did not get any answers.  I just replaced the blade grips on my MSR. The parts from Horizon Hobby came with the brass...
01-14-2010, 09:46 PM
Replies: 9
Views: 1,695
Posted By bcr1953chevy

RE: Help with new mSR

Does the new one work correctly?

How long did it take them to reply to you and provide a replacement?
01-14-2010, 08:01 AM
Replies: 28
Views: 10,993
Posted By bcr1953chevy

Blade MSR Main Rotor Grips - Washers and O-Rings

I'm replacing the main rotor grips on my Blade MSR. I ordered and received replacement grips from Horizon Hobby. The new grips came with metal washers and o-rings. The exploded parts drawing in the...
01-13-2010, 12:00 PM
Replies: 40
Views: 12,602
Posted By bcr1953chevy

RE: Help with flimsy/breakable Blade mSR struts

Put the gear on it this morning before I left for work. Did not have a change to fly it yet but the landing gear did fit into the holes in the body. If you make the same repair that I did, be careful...
01-13-2010, 03:27 AM
Replies: 17
Views: 4,927
Posted By bcr1953chevy

RE: MSR - is the DX6i worth buying?

I read the PDF file and configured my transmitter per the document. I have to make some repairs from the last "landing" so I've not had an opportunity to fly it using the new settings. I am a bit...
01-13-2010, 03:12 AM
Replies: 40
Views: 12,602
Posted By bcr1953chevy

RE: Help with flimsy/breakable Blade mSR struts

My indoor flying space is only about 12 FT x 14 FT with a 7 FT ceiling. I'm pretty new at helicopters and my Blade MSR is only about two weeks old. Most of my flights end in a hard landing. So far,...
01-10-2010, 09:13 PM
Replies: 17
Views: 4,927
Posted By bcr1953chevy

RE: MSR - is the DX6i worth buying?

Iclicked on the link for the PDFdocument. It started loading but after a few seconds, the word Stopped is displayed at the bottom of my browser and it appears to freeze. Ifound the forum where the...
01-09-2010, 07:06 PM
Replies: 2
Views: 1,673
Posted By bcr1953chevy

RE: An easy way to balance MSR blades

Great idea! Ijust purchased a Blade MSR. It rotates slowly while hovering and I can't trim it out. It appears to rotate in small steps, not smoothly. I was wondering if my flybar was balanced. I'll...
Showing results 1 to 25 of 45
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.