RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: paterson1039
Showing results 1 to 13 of 13
Search took 0.22 seconds.
07-12-2015, 08:17 PM
Replies: 5,548
Views: 517,314
Posted By paterson1039

Angry wipeout. 3660SL 3180kv

So i slapped a 3660SL 3180kv Brushless Inrunner (WaterCooled) (http://hobbyking.com/hobbyking/store/uh_viewItem.asp?idProduct=25091) on my aquacraft with an x60 amp esc. with one 3200 mah 11.1v...
06-04-2010, 10:16 PM
Replies: 7
Views: 1,506
Posted By paterson1039

RE: T6exap For heli?

http://www.futabarc.com/radios/futk62.html

This is the link to the remote in which i own.
06-04-2010, 10:12 PM
Replies: 7
Views: 1,506
Posted By paterson1039

RE: T6exap For heli?

I am really confused, on the box it says For Airplane Model / For Helicopter Model

Also, the model is a "T6EXAP" which is not listed on that comparison chart you posted... Is this differant than...
05-31-2010, 02:02 PM
Replies: 7
Views: 1,506
Posted By paterson1039

T6exap For heli?

does anyone know if the T6exap will work for a heli? if so does anyone know how to set it up for a trex or have a link to someinformation that shows how? The manual only has information on planes.</p>
05-23-2010, 10:07 PM
Replies: 6
Views: 891
Posted By paterson1039

RE: Help! Rx/Tx from G2 into Trex450 questions

So does anyone have any idea what i should do as far as dip switches on the wk-2601??
05-22-2010, 12:17 PM
Replies: 6
Views: 891
Posted By paterson1039

RE: Help! Rx/Tx from G2 into Trex450 questions

when you say left and right aileron, are you talking about looking at the heli with the tail pointed away from you, or with the tail pointed toward you?
05-22-2010, 01:20 AM
Replies: 6
Views: 891
Posted By paterson1039

Help! Rx/Tx from G2 into Trex450 questions

I gutted my exceed G2, and put the parts from it into my new trex450 carbon fiber heli. I cannot figure out how to hook up the servos to my receiver. I need to know the location of the servos to...
05-11-2010, 09:06 PM
Replies: 19
Views: 2,837
Posted By paterson1039

RE: T Rex Clones???

OK, I have been doing a lot of research, and from what i see, the clones tend to be manufactured in a hurried process... No locktight, bad instructions.. etc.. etc.. I am looking for a carbon fiber...
05-10-2010, 01:17 PM
Replies: 19
Views: 2,837
Posted By paterson1039

RE: T Rex Clones???

I am looking at the 400-450 size. Isaw a few clones like the EXI brand and Copter X, for relatively cheap. my budget is under 200 shipped, and i do not need servo's, remote etc..
05-10-2010, 01:11 AM
Replies: 19
Views: 2,837
Posted By paterson1039

T Rex Clones???

How are these "clones" are they really as good as their counterparts? What are their downfalls, and is it a good idea to buy the frame cheap and put good electronics in them? Usefull information...
04-26-2010, 11:34 PM
Replies: 2
Views: 1,000
Posted By paterson1039

RE: Tail Servo issues Raptor G2

Update: after numerouse youtube videos... i figured out that my heli has the heading hold function, which is why it reacts this way when it is not running.... when i fly it, it performs flawlessly......
04-26-2010, 09:52 PM
Replies: 2
Views: 1,000
Posted By paterson1039

RE: Tail Servo issues Raptor G2

I have been doing more research on this, I think i may have a gyro issue, when the heli is sitting still, i can see the servo twitching back and forth with noone touching it... I am not sure but i...
04-26-2010, 08:49 PM
Replies: 2
Views: 1,000
Posted By paterson1039

Tail Servo issues Raptor G2

I just purchased a Raptor G2, put the battery in after full charge and headed to indoor warehouse for flight. It was hovering at 2 inches perfectly for about 3-4 minutes, had excellent controll over...
Showing results 1 to 13 of 13


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.