RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: crobara
Showing results 1 to 15 of 15
Search took 0.18 seconds.
Forum: Gas Engines
04-10-2021, 11:44 AM
Replies: 6
Views: 1,619
Posted By crobara

They are just full of gunk. I will try cleaning...

They are just full of gunk. I will try cleaning with a tap but don't know if that will clean enough for thread locker on the new muffler.
Forum: Gas Engines
04-09-2021, 01:03 PM
Replies: 6
Views: 1,619
Posted By crobara

Thanks for the data. Even though the smaller...

Thanks for the data. Even though the smaller muffler fits on the DLE30 I took it off. Guessing it would cause too much back pressure. Can you recommend a good way to clean out the threads on the...
Forum: Gas Engines
04-09-2021, 10:23 AM
Replies: 6
Views: 1,619
Posted By crobara

These have the same bolt pattern but one is much...

These have the same bolt pattern but one is much smaller in size than the other. I was thinking of trying the smaller one because the larger has a broken pipe but I didn't want to overheat or cause...
Forum: Gas Engines
04-07-2021, 04:12 PM
Replies: 6
Views: 1,619
Posted By crobara

same muffler for dle 20 & 30

One of my dl3 30's has a smaller muffler than the other. Is it ok to run a dle 20 muffler on a dle30?
Forum: Beginners
07-22-2019, 12:04 AM
Replies: 25
Views: 11,241
Posted By crobara

Great info. I am working with a Saito 14c gas...

Great info. I am working with a Saito 14c gas engine and your info seems to apply to it as well. I have trouble getting sufficient rpm.
Forum: Gas Engines
05-01-2019, 10:01 AM
Replies: 1
Views: 1,175
Posted By crobara

Saito fg-14c

I have read Al's "Engine Tuning 101" and would like to know if his document can be applied to the 14c which is a gas four stroke. Or is there another document like this one that applies to Saito 4...
Forum: Gas Engines
04-30-2019, 09:50 PM
Replies: 6
Views: 4,111
Posted By crobara

I have been flying my 14c for about 12 flights...

I have been flying my 14c for about 12 flights after break in at 20:1 and can only on occasion get the engine to run up to 8k. I'm thinking of changing my mix to a little less oil, assuming that 20:1...
Forum: Questions and Answers
04-17-2019, 10:31 AM
Replies: 41
Views: 16,497
Posted By crobara

Thanks cudda.

Thanks cudda.
Forum: Questions and Answers
04-15-2019, 04:01 PM
Replies: 41
Views: 16,497
Posted By crobara

Hello anyone still out there regarding this...

Hello anyone still out there regarding this issue? When you run one battery do you use an empty slot on the receiver to provide the power to the ignition module?
Forum: Electric Pattern Aircraft
08-19-2015, 02:19 PM
Replies: 80
Views: 28,461
Posted By crobara

Thanks Bo but my washer has an i.d. of .500 all...

Thanks Bo but my washer has an i.d. of .500 all the way through. I contacted the supplier and he is sending me a correct part.
Forum: Electric Pattern Aircraft
08-16-2015, 07:51 PM
Replies: 80
Views: 28,461
Posted By crobara

I just received my hacker a60 v2 and the outer...

I just received my hacker a60 v2 and the outer prop washer has a large hole that the prop nut just seems to slop around in. Is this normal and does it self center itself when tightened down?
Forum: ARF or RTF
12-02-2010, 05:46 PM
Replies: 437
Views: 85,860
Posted By crobara

RE: *Hangar 9 New Pulse 125*

Joe Mamma - I looked at post 152 and didn't see any pics. Maybe I don't know how to view the pics.
Forum: ARF or RTF
12-02-2010, 03:20 PM
Replies: 437
Views: 85,860
Posted By crobara

RE: *Hangar 9 New Pulse 125*

I am purchasing an older pulse 125 and have a question regarding the tail assembly. Are the stab and rudder together as an assembly and then that assembly is attached to the fuse? Is the epoxy needed...
Forum: Beginners
09-09-2010, 01:11 PM
Replies: 5
Views: 1,057
Posted By crobara

RE: balancing an ultra stick 40 with O.S. 61motor

Thanks for your help. When searching around for info on lateral balancing I couldn't find any examples regarding side mounted engines except one that suggested it wasn't a big deal because the...
Forum: Beginners
09-08-2010, 06:04 PM
Replies: 5
Views: 1,057
Posted By crobara

balancing an ultra stick 40 with O.S. 61motor

Hello -I recently picked up an Ultra Stick 40 plane that has an o.s. 61 motor on it. In checking the lateral balance I found that the right wing dips way down. I set a couple of ounces on the left...
Showing results 1 to 15 of 15


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.