RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: mkguyUK
Showing results 1 to 14 of 14
Search took 0.64 seconds.
Forum: RC Jets
05-03-2005, 12:19 PM
Replies: 2,661
Views: 396,250
Posted By mkguyUK

RE: new Arf Boomerang 14lb thrust

Thanks for the tips on the supplementry tank guys.....

I will how long 2 litres on a Wren 54 mark 3 runs and see....
Forum: RC Jets
05-03-2005, 10:17 AM
Replies: 2,661
Views: 396,250
Posted By mkguyUK

RE: new Arf Boomerang 14lb thrust

I have seen those supplementry tanks and always wondered how they were plumbed in? Anyone care to share?


Andrew
Forum: RC Jets
04-30-2005, 09:45 PM
Replies: 2,661
Views: 396,250
Posted By mkguyUK

RE: new Arf Boomerang 14lb thrust

Thats awful news Sandor.....

Its terrible to see the Boomer in bits like that....

Glad the Turbine and servos are ok though.. From the ashes the Pheonix will rise again eh?


Andrew
Forum: RC Jets
04-29-2005, 05:29 PM
Replies: 2,661
Views: 396,250
Posted By mkguyUK

RE: new Arf Boomerang 14lb thrust

Sandor

You are without doubt 'Da Man.... Lovin your smoke system.... :)

Not sure how you are going to explain the blue streak on the lawn and the stains on your hands... Try this...
Forum: RC Jets
04-27-2005, 08:21 AM
Replies: 2,661
Views: 396,250
Posted By mkguyUK

RE: new Arf Boomerang 14lb thrust

Funny you should say that Sandor...

I had to tweeak mine this morning as the bolts were a shade too far in (half a turn) I repositioned them and one of the blind nuts inside the wing had...
Forum: RC Jets
04-23-2005, 12:15 PM
Replies: 2,661
Views: 396,250
Posted By mkguyUK

RE: new Arf Boomerang 14lb thrust

Re the FOD guard, I bought a mesh strainer for £1 and used a rubber grommet to hold it in place, the grmmet has a channel built in to hold the rough edges from the cut mesh, I reckon that with the...
Forum: RC Jets
04-23-2005, 10:49 AM
Replies: 2,661
Views: 396,250
Posted By mkguyUK

RE: new Arf Boomerang 14lb thrust

Hi Simon

Thanks for your offer, I will post the DVD out to you....
Forum: RC Jets
04-23-2005, 04:39 AM
Replies: 2,661
Views: 396,250
Posted By mkguyUK

RE: new Arf Boomerang 14lb thrust

It about 5 gig DV quality raw AVI and compressed to around 1 gig for DVD format VOB etc..... I am quite happy to send the DVD to someone who can host that size file...... I got some nice planes on...
Forum: RC Jets
04-23-2005, 12:34 AM
Replies: 2,661
Views: 396,250
Posted By mkguyUK

RE: new Arf Boomerang 14lb thrust

Hi Ian

I posted the pic at the res I downloaded it from, you can always email me at [email protected] and I will send you it via email, it might come out better, I printed it using a ink...
Forum: RC Jets
04-21-2005, 03:09 AM
Replies: 2,661
Views: 396,250
Posted By mkguyUK

RE: new Arf Boomerang 14lb thrust

Mine is coming along well, about another week ot tinkering should see it ready for it's maiden flight...

On the nose wheel issue, I installed the main's first with the view of getting the...
Forum: RC Jets
04-08-2005, 09:38 PM
Replies: 2,661
Views: 396,250
Posted By mkguyUK

RE: new Arf Boomerang 14lb thrust

Mine is coming along nicely..... Most of the build work is done..... I just need to install the noseleg, I will measure up to ensure the the jet sits right before putting the bend in.... Most of...
Forum: RC Jets
03-31-2005, 10:16 PM
Replies: 2,661
Views: 396,250
Posted By mkguyUK

RE: new Arf Boomerang 14lb thrust

I picked up my Boomerang kit direct from Alan yesterday..... All looking good so far, I made up my shopping list of the hardware to finish it...... I have a Wren 54 as the powerplant....

I am...
Forum: RC Jets
07-30-2003, 11:54 PM
Replies: 3
Views: 605
Posted By mkguyUK

Thanks

I have checked the setup via the Trim instructions, there are two air nipples on the unit, one is in line with the valve and the other is offset, in the instructions it states the inline one is the...
Forum: RC Jets
07-30-2003, 11:35 PM
Replies: 3
Views: 605
Posted By mkguyUK

Help with Trim Wheel Brakes

Hope some of you guys can help me........ I am venturing into Turbines for the first time and have got a Kangeroo with a phoenix 4 20lb power plant.

I have had quite a lot of work to do on it...
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.