RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Search
Today's Posts
Mark Forums Read
Vendor Directory
Notices
 
Page 1 of 3
1
2
3
Search: Posts Made By: jspauld2
Showing results 1 to 25 of 65
Search took 0.12 seconds.
Forum: Gas Engines
02-25-2016, 08:11 AM
Replies: 2,806
Views: 704,284
Posted By jspauld2

Timbers, That is good info to know. I don't...

Timbers,

That is good info to know. I don't know if that is definitively too high, but it certainly couldn't hurt to try and bring the temps down a bit.

I shoot for less than 300°F for...
Forum: Gas Engines
02-25-2016, 08:05 AM
Replies: 2,806
Views: 704,284
Posted By jspauld2

For anyone who is interested, Saito just released...

For anyone who is interested, Saito just released a collector ring for the FG-60R3 that we will be shipping later this month. It is item number: SAIG60R3171 and the link.is below. I apologize for...
Forum: Gas Engines
02-25-2016, 07:50 AM
Replies: 2,806
Views: 704,284
Posted By jspauld2

[QUOTE=cathurga;12179856]...I have a telemetry...

[QUOTE=cathurga;12179856]...I have a telemetry module attached to cylinder 1 and I set the alarm at 150 Deg Celsius. I only ever got one alarm and that is after a few circuits of FULL throttle into a...
Forum: Gas Engines
02-18-2016, 02:57 PM
Replies: 2,224
Views: 444,148
Posted By jspauld2

I did know that, but forgot the issue with...

I did know that, but forgot the issue with servicing Australia. We will make every effort to support the engine regardless of your location. If you run into any issues, please just contact me...
Forum: Gas Engines
02-18-2016, 09:38 AM
Replies: 2,224
Views: 444,148
Posted By jspauld2

We have not tested that at Horizon since the OS...

We have not tested that at Horizon since the OS GGT has been released.. Early on in the 10cc development, we did experiment with running gas on a glow plug. Ultimately, we decided the benefits did...
Forum: Gas Engines
02-18-2016, 08:10 AM
Replies: 2,224
Views: 444,148
Posted By jspauld2

Not every engine had the problem. It was an...

Not every engine had the problem. It was an isolated case with a few of the early engines. It is entirely possible that you may have one of the bad cranks. We will stand behind the product...
Forum: Glow Engines
01-27-2016, 06:47 AM
Replies: 2,647
Views: 520,203
Posted By jspauld2

That's not a bad idea. I do not know the...

That's not a bad idea. I do not know the specifics needed for the input on the TM1000, and you may fry one or two along the way, but I think the theory might work. As long as you are careful with...
Forum: Glow Engines
01-26-2016, 02:41 PM
Replies: 2,647
Views: 520,203
Posted By jspauld2

Pete, I don't believe there are any extra wires...

Pete,
I don't believe there are any extra wires included with the engine.

As for the telemetry, unfortunately there is no 'plug and play' option out there. The built-in telemetry feedback is...
Forum: Gas Engines
01-26-2016, 02:12 PM
Replies: 2,224
Views: 444,148
Posted By jspauld2

Rick, unfortunately we are unable to do that. We...

Rick, unfortunately we are unable to do that. We can provide the parts, but you will have to make the change yourself as we cannot guarantee the engine after the modifications.



Ahicks, if you...
Forum: Glow Engines
01-12-2016, 10:45 AM
Replies: 2,647
Views: 520,203
Posted By jspauld2

Tom, thanks for your dedication to this engine...

Tom, thanks for your dedication to this engine and this thread! Although it is difficult to monitor all threads that discuss our products, we try to check in on these threads occasionally to see...
Forum: Gas Engines
10-26-2015, 08:35 AM
Replies: 2,224
Views: 444,148
Posted By jspauld2

In regards to the ignition voltage range: The...

In regards to the ignition voltage range: The posted numbers are absolute limits, not nominal. As with many ratings, often times you are able to supply voltages outside of this range and the...
Forum: Gas Engines
12-22-2014, 12:19 PM
Replies: 14
Views: 7,381
Posted By jspauld2

Brones, You are correct. I am sorry that...

Brones,

You are correct. I am sorry that someone told you that was normal, it definitely is not. I will get you in contact with someone to send you a new muffler free of charge.

Thanks,
Jimmy
Forum: Gas Engines
12-12-2014, 07:19 AM
Replies: 2,224
Views: 444,148
Posted By jspauld2

Jeff, It's been so long since we had a 10GX...

Jeff,

It's been so long since we had a 10GX mounted in that airplane that I've forgotten what setup we had. If you remove the center section, you will lose some performance. There are...
Forum: Gas Engines
12-02-2014, 09:38 AM
Replies: 239
Views: 60,117
Posted By jspauld2

fly24-7 The following pdf...

fly24-7

The following pdf [ATTACH]2051628[/IMG] should get you the dimension you need.

Thanks,
Jimmy
Forum: Gas Engines
11-25-2014, 10:01 AM
Replies: 239
Views: 60,117
Posted By jspauld2

The threads are M3. If your local hardware store...

The threads are M3. If your local hardware store does not have anything (I would look there first), we have some different items that would have the screws you need.

DYN6018...
Forum: Gas Engines
11-25-2014, 08:10 AM
Replies: 2,224
Views: 444,148
Posted By jspauld2

Jeff, It is a little heavier, but not overly...

Jeff,

It is a little heavier, but not overly heavy. For this airplane, the 10cc or 15cc choice is purely preferential, both engines fly the airplane well in their own rights. If you don't plan...
Forum: Gas Engines
11-25-2014, 07:25 AM
Replies: 239
Views: 60,117
Posted By jspauld2

The short answer is that it is possible. What...

The short answer is that it is possible. What hessian said is true. It may be easier to buy a replacement crankcase and swap out all of the internal components. That way you would avoid any drill...
Forum: Gas Engines
11-25-2014, 07:10 AM
Replies: 2,224
Views: 444,148
Posted By jspauld2

I would tend to agree with ahicks. We did...

I would tend to agree with ahicks. We did initial 10GX development testing with the Katana, but found that the 15GX was a better combo for 3D flying. 10GX on the Katana is a good sport combination.
Forum: Gas Engines
11-10-2014, 05:16 AM
Replies: 239
Views: 60,117
Posted By jspauld2

Hessian, You are correct in that you do not...

Hessian,

You are correct in that you do not need to use the port on the muffler. We included the port on the muffler in case you wanted to run a smoke system with this engine. You can plug the...
Forum: Gas Engines
10-15-2014, 07:29 PM
Replies: 2,224
Views: 444,148
Posted By jspauld2

Al, Why are you pulling the carb? From the...

Al,

Why are you pulling the carb? From the sounds of it, the carburetor is working perfectly fine. The way your engine/fuel tank is set up it just siphons fuel for a moment while fueling. There...
Forum: Gas Engines
10-15-2014, 02:45 PM
Replies: 2,224
Views: 444,148
Posted By jspauld2

In reply to the regulator question, it basically...

In reply to the regulator question, it basically just ensures that there is a little more consistency to the fuel flow/pressure than normal. It is not an effective pump, but it has some pumping...
Forum: Gas Engines
09-23-2014, 09:18 AM
Replies: 2,224
Views: 444,148
Posted By jspauld2

Sorry for taking so long to reply. I would set...

Sorry for taking so long to reply. I would set your alarm to go off at 300°F. If you can maintain the operating temperature below this, the engine should be getting enough cooling. If it is...
Forum: Gas Engines
09-19-2014, 08:10 AM
Replies: 2,224
Views: 444,148
Posted By jspauld2

Unfortunately the 3 to 1 rule is not a good...

Unfortunately the 3 to 1 rule is not a good starting point. Pe Reivers had a really, really good forum that had research, examples, and information regarding cooling of model engines (as well as...
Forum: Gas Engines
05-01-2014, 12:35 PM
Replies: 16
Views: 13,197
Posted By jspauld2

Hi opspro, Was the 15x6 you tried to run a...

Hi opspro,

Was the 15x6 you tried to run a 2-blade or was it a 3- or 4-blade? A 14x8 4-blade is a heavy prop, but I would think it should turn it either way.

Out of curiosity, when did you...
Forum: Gas Engines
02-17-2014, 07:04 AM
Replies: 41
Views: 10,694
Posted By jspauld2

Basil, I would tend to agree with Jerry on...

Basil,

I would tend to agree with Jerry on this. It is not typical of this engine to operate like you have described if it is properly setup. Your problem indeed sounds like an ignition issue...
Showing results 1 to 25 of 65
 
Page 1 of 3
1
2
3


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.