RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: bigbobed
Showing results 1 to 25 of 68
Search took 0.68 seconds.
11-21-2010, 02:52 PM
Replies: 44
Views: 19,680
Posted By bigbobed

RE: 1929 Travel Air

Yes. The bolts go through the firewall.
11-21-2010, 07:39 AM
Replies: 10
Views: 2,147
Posted By bigbobed

RE: Multiplex harness

I bought the Madison Products harness and am quite satisfied with it. Much more comfortable than the neck strap.
Had to change the eye bolts from bent to straight and shorten them to accommodate...
Replies: 10
Views: 2,147
Posted By bigbobed

RE: Multiplex harness

I already have a tray that I use with a neck strap. Thought the shoulder one would be more comfortable. Also could leave the harness on and just unclip the tray when not flying.
Replies: 10
Views: 2,147
Posted By bigbobed

RE: Multiplex harness

Looks like they only do business in the UK. Here's another option.
http://www.qualityrcproducts.com/prod_harness.html

Bob
Replies: 10
Views: 2,147
Posted By bigbobed

RE: Multiplex harness

Any idea where to order?
Replies: 10
Views: 2,147
Posted By bigbobed

Multiplex harness

Is the European style Multiplex tray harness available in the US?
01-18-2008, 05:23 PM
Replies: 2
Views: 820
Posted By bigbobed

RE: 9303(2.4)/DX7 Data Transfer

I did what you describe. There were some minor trim adjustments required, but certainly easier than starting from scratch.
01-18-2008, 03:40 PM
Replies: 3
Views: 822
Posted By bigbobed

RE: 9303 snap roll problem

I'd call them outside snaps. With up elevator the canopy is on the inside of the roll. With down elevator the canopy is on the outside of the roll. Both are entered from straight, level upright...
01-18-2008, 10:56 AM
Replies: 3
Views: 822
Posted By bigbobed

9303 snap roll problem

If I set the snap roll switch to r-u or l-u every thing is fine. If I program l-d or r-d, the rudder and ailerons move in opposite directions. I have three other models programmed and they work...
11-14-2007, 12:14 PM
Replies: 0
Views: 496
Posted By bigbobed

9303 AR6200 problem

Powered up the 9303 and then the AR6200. Elevator went to full down and the esc did not arm. Found that moving the rudder control moved the elevator. Re-bound the receiver and everything seemed all...
08-25-2007, 03:18 PM
Replies: 4
Views: 969
Posted By bigbobed

RE: What's this?

That's not a binding plug.
08-25-2007, 05:56 AM
Replies: 4
Views: 969
Posted By bigbobed

What's this?

Came with my DX7.

Thanks,

Bob
07-28-2007, 04:40 PM
Replies: 1
Views: 562
Posted By bigbobed

RE: Chan 04 Crystal

Hopefully I've found one. Keeping my fingers crossed.
07-28-2007, 07:45 AM
Replies: 1
Views: 562
Posted By bigbobed

Chan 04 Crystal

I have an R148DF 50mhz on order but chan 04 crystal doesn't seem to be available. Is there any other source for this crystal?

Thanks,

Bob
07-11-2007, 12:40 PM
Replies: 2
Views: 633
Posted By bigbobed

RE: 9C SUPER FASST?

Here's the page in question.
07-11-2007, 07:32 AM
Replies: 2
Views: 633
Posted By bigbobed

9C SUPER FASST?

I have a brochure that I picked up at Joe Nall. It lists a 9c Super FASST setup, but I cannot find any reference to it online. Is such a thing in the pipeline, or was it dropped after the brochure...
04-06-2007, 02:13 PM
Replies: 7
Views: 1,843
Posted By bigbobed

RE: 12Z 2.4 conversion

Will the 50 MHZ version work with existing R148DF rcvrs?

Thanks,

Bob
12-06-2006, 01:10 PM
Replies: 732
Views: 110,343
Posted By bigbobed

RE: Transall C-160

Wasn't trying to hijack the thread. Probably should've sent Charlie a pm. Up until I moved a month ago, I belonged to the same club and like to yank his chain once in a while.
The video was an...
12-05-2006, 08:57 PM
Replies: 732
Views: 110,343
Posted By bigbobed

RE: Transall C-160

Charlie (gman), forget the C130 and spend you electric bucks here.
http://www.jethangar.com/Index/index.html
11-01-2006, 05:49 PM
Replies: 732
Views: 110,343
Posted By bigbobed

RE: Transall C-160

Hey gman, since when did you start checking cg's? I thought if you took off and cleared the fence, range check and cg were ok.
11-01-2006, 08:44 AM
Replies: 732
Views: 110,343
Posted By bigbobed

RE: Transall C-160

http://iflyrc.hypermart.net/CG%20Machine.htm
Works great on any size plane. Both hands free to move stuff around. I use two plumb bobs, one on each side to make sure it's lined up properly.
07-01-2006, 10:55 AM
Replies: 5
Views: 808
Posted By bigbobed

RE: 4star 60

I don't think you will be happy with that combo. I have an AXI 4120-18 in mine with 6s li-poly. Performance is good but not breath taking. My 2826 is in a 5 lb plane on 4s li-poly so I have a...
01-10-2006, 03:28 PM
Replies: 118
Views: 16,052
Posted By bigbobed

RE: Hangar 9 33% Edge 540 - Part 3

My son had the same problem. After replacing everything, he finally solved the problem with a toroid around the esc lead. He found one at his lhs. Here's another possibility....
Replies: 9
Views: 958
Posted By bigbobed

RE: Outrunner Motor Question

Here's how to do it.
http://www.maxxprod.com/pdf/HC-Shaft-Service.pdf
Showing results 1 to 25 of 68
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.