RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Search
Today's Posts
Mark Forums Read
Vendor Directory
Notices
Search: Posts Made By: N1903Z
Showing results 1 to 17 of 17
Search took 0.64 seconds.
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
08-26-2008, 04:40 PM
Replies: 177
Views: 40,291
Posted By N1903Z

RE: What was your first Radio?

1967: Testors brand. Galloping Ghost system. Single channel rudder only. 27mHz, I think. Came with a 1/2A hand launch plane.
Forum: ARF or RTF
04-30-2006, 08:41 PM
Replies: 7,471
Views: 709,961
Posted By N1903Z

RE: New Hanger 9 p-51 mustang **Trainer?!?**

Hi justflie, congrats on the successful maiden. One thing to keep in mind while troubleshooting your problem with the tx charger is that the JR charger output plug is wired different than most others...
Forum: Hitec/MultiPlex Radios- Ask Hitec Customer Service
02-11-2005, 04:51 AM
Replies: 5
Views: 834
Posted By N1903Z

RE: Optic 6 & AMA Insurance

HI, CFIMEI

I'm just curious. Are you an attorney?
Forum: Brushed/Brushless motors, speed controls, gear drives
10-02-2004, 02:27 PM
Replies: 3
Views: 636
Posted By N1903Z

RE: ESC question

The 4.8v cut-off is for an entire pack (not per cell) and is too low because a 2 cell lipo pack will need a cut-off at 6v. A 3 cell lipo pack will need a 9v cut-off. Assuming cells are wired in...
Forum: Polks Hobby
08-07-2004, 04:23 PM
Replies: 1
Views: 691
Posted By N1903Z

Tracker II Scanner

Hi Everyone! I really like my Tracker II (Ver. 1.35) so far. I've had it for over 1 month now and have at least 3 hours total operating time on it now. The built-in channel scanner is great and has...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
07-31-2004, 04:22 PM
Replies: 2
Views: 2,532
Posted By N1903Z

RE: Throttle Elevator Mixing

Hi rightflyer! I tried it on a Hobbico Superstar 40 RTF which has a flat bottomed wing airfoil. The high climb rate of the Superstar 40 at higher throttle settings is caused by the increased lift due...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
06-20-2004, 02:12 PM
Replies: 32
Views: 1,980
Posted By N1903Z

RE: repaireing reciever antennas!

Jon, yours is a very good explaination as to why the antenna wire is shorted to ground at the DC level but not at the rf of 72 MHz. Thanks.
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
06-20-2004, 03:25 AM
Replies: 32
Views: 1,980
Posted By N1903Z

RE: repaireing reciever antennas!

Well, here's my $.02 on this. What I discovered with my Ohm meter is that on all my different brand of RX's, there are zero Ohms (100% continuity) between the negative (-) terminal of the battery and...
Forum: Questions and Answers
06-19-2004, 03:02 AM
Replies: 14
Views: 1,088
Posted By N1903Z

RE: Polk Seeker II

Any progress on finding the problem with the Seeker IIs, Speedbird? Can't believe four bad Seeker IIs. Thanks.
Forum: Electric RC Jets
04-10-2004, 11:05 PM
Replies: 7
Views: 1,888
Posted By N1903Z

RE: GWS a10 EDF 50 problems...

I think just about everyone that has been successful with the GWS A-10 has found that it flies best with the cg at 57mm behind the L.E. .
They have also discovered that they had to add almost full...
Forum: Scratch Building, Aircraft Design, 3D/CAD
01-31-2004, 03:33 AM
Replies: 4
Views: 1,888
Posted By N1903Z

RE: SR-71 from RCM plans.

Hi clam61,
Yes, it is a flying model: http://www.parkermodel.com/htmlsr71.html
If you are a subscriber to RCM magazine, the article is available at their website online: ...
Forum: Scratch Building, Aircraft Design, 3D/CAD
01-27-2004, 05:39 PM
Replies: 4
Views: 1,888
Posted By N1903Z

RE: SR-71 from RCM plans.

Thanks, Wingman for your response. I do plan on posting a build thread when I get started. Can't say for sure when that will be though.
-----
Carl
Forum: Scratch Building, Aircraft Design, 3D/CAD
01-26-2004, 06:35 AM
Replies: 4
Views: 1,888
Posted By N1903Z

SR-71 from RCM plans.

Hi all,
Anyone building the SR-71 (plan no. 1313) featured in the July 2002 RCM construction article? I received the plans and have been studying them before starting construction. Thought it...
Forum: Scratch Building, Aircraft Design, 3D/CAD
01-12-2004, 09:17 PM
Replies: 16
Views: 1,214
Posted By N1903Z

RE: Two possible building tables - neither is straight!

CafeenMan, thanks for your answer. I thought about magnets after my original post. The ceiling tile is a great idea if having to pin.
Forum: Scratch Building, Aircraft Design, 3D/CAD
01-12-2004, 06:46 PM
Replies: 16
Views: 1,214
Posted By N1903Z

RE: Two possible building tables - neither is straight!

Something I've always wondered is: How do you get T-pins (they hold parts in place while gluing, sheeting, laminating,
assembly, etc.) to stick into a glass or steel building table?...
Forum: Glow Engines
12-13-2003, 08:29 PM
Replies: 16
Views: 1,632
Posted By N1903Z

RE: what is the Castor oil?

A few more facts about the castor oil plant:
Scientific name: Ricinus communis (does the first part of its name ring a bell? RICINus? Ricin is one of the most poisonous toxins known to man. Just...
Forum: Glow Engines
11-23-2003, 12:32 AM
Replies: 5
Views: 624
Posted By N1903Z

RE: Engine running strangely

My Evolution trainer engine was doing the exact same thing right out of the box until in frustration I removed the baffle from the muffler. Its been running great ever since. Just a tad more noisy...
Showing results 1 to 17 of 17


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.