RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Search
Today's Posts
Mark Forums Read
Vendor Directory
Notices
Search: Posts Made By: aeromax18
Showing results 1 to 11 of 11
Search took 0.04 seconds.
Forum: Electric RC Jets
10-15-2018, 09:51 AM
Replies: 115
Views: 67,955
Posted By aeromax18

Improvements update: I dropped a new power...

Improvements update:
I dropped a new power system in the Twister. A 12 blade Change Sun fan with a Cyclone Power CR480-2900-40DF. Suppose to provide 1.65kg of thrust. I also increased the Thrust...
Forum: Electric RC Jets
10-07-2018, 10:53 AM
Replies: 115
Views: 67,955
Posted By aeromax18

Cobrajocky, I looked it up (f16 - Pase 3) but...

Cobrajocky,
I looked it up (f16 - Pase 3) but it 's been discontinued. Where can I get one?
I spent few hours reading and learning the facts about EDF intake and Trust tubes. I feel like I know...
Forum: Electric RC Jets
09-27-2018, 01:02 PM
Replies: 115
Views: 67,955
Posted By aeromax18

cobrajocky You are right . that seemed to have...

cobrajocky
You are right . that seemed to have been the problem. I remember your advise for cutting the inlets opening wider but then on the other hand I was quite happy with its flight with the...
Forum: Electric RC Jets
09-26-2018, 01:04 PM
Replies: 115
Views: 67,955
Posted By aeromax18

Finally Maidened the Twister

,Hi guys
I see nothing happened here foe a while. I veered off to other airplanes and then last week decided to get the Twister in the air. Decided to fly it first with the stock set up. I got about...
Forum: Electric RC Jets
02-19-2018, 08:23 AM
Replies: 115
Views: 67,955
Posted By aeromax18

Thanks for your input here. I read thru this...

Thanks for your input here. I read thru this thread before starting assembling the Twister but found no hint of modifying the intakes or adding a cheater hole by any of the guys that upgraded it. . I...
Forum: Electric RC Jets
02-18-2018, 12:21 PM
Replies: 115
Views: 67,955
Posted By aeromax18

cobrajocky, Can you shoot me a couple of photos...

cobrajocky, Can you shoot me a couple of photos showing what you did on the inlets and extra scoop on the bottom? A picture is worth a thousand words.
Thanks
Forum: Electric RC Jets
02-15-2018, 02:55 AM
Replies: 115
Views: 67,955
Posted By aeromax18

cobrajocky, This makes a lot of sense. . I...

cobrajocky,
This makes a lot of sense. . I think that since I'm getting as much as one to one power to weight ratio on the stock fan with 4's I'll try that first and see how it goes.
Thank you
Forum: Electric RC Jets
02-14-2018, 08:02 AM
Replies: 115
Views: 67,955
Posted By aeromax18

Last week I tested the original fan/motor that...

Last week I tested the original fan/motor that came with the Twister. I placed the fuse with the fan installed and a 4 cell battery on a digital scale reading 980 grams of weight. I proceeded to...
Forum: Electric RC Jets
02-04-2018, 01:46 AM
Replies: 115
Views: 67,955
Posted By aeromax18

Hey Guys, Thanks for the input. I'm still...

Hey Guys,
Thanks for the input. I'm still waiting on my power / fan set up from Turbine RC. As for the paint I am going to use a Felt tip Permanente marker. I tried it before and it works great. It...
Forum: Electric RC Jets
01-20-2018, 10:51 AM
Replies: 115
Views: 67,955
Posted By aeromax18

Still Bill / Markind, .Thanks I'm upgrading as...

Still Bill / Markind, .Thanks
I'm upgrading as that is what most everyone recommends.
Forum: Electric RC Jets
01-19-2018, 05:37 AM
Replies: 115
Views: 67,955
Posted By aeromax18

Hello Guys,I hope this forum is not totally dead....

Hello Guys,I hope this forum is not totally dead. I just picked up a Twister kit and before gluing both fuselage halves I wanted to check how would the fan and motor fit. to my surprise the fan...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.