RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: flygono
Showing results 1 to 16 of 16
Search took 0.58 seconds.
Forum: RC Jets
09-26-2020, 05:36 AM
Replies: 135
Views: 39,732
Posted By flygono

stab incidence

I crash my COMP ARF DG 800S and in order to repair I would want to know the stab incidence in relation to the wing incidence at the root where it meats the fuse. I should have measure it especially...
Forum: Gas Engines
05-18-2020, 04:37 AM
Replies: 253
Views: 98,125
Posted By flygono

Thanks Tom for the information but before sending...

Thanks Tom for the information but before sending the engine I noticed that the rear cylinder spark plug is not firing. I exchanged the spark plug an it's not the culprit. It's either the Electronic...
Forum: Gas Engines
05-13-2020, 08:59 AM
Replies: 253
Views: 98,125
Posted By flygono

Does anyone know where can these engines serviced...

Does anyone know where can these engines serviced in USA?
I have a il 135 that has not run in last 3 years after I crashed my COMP ARF Mustang and I cannot get it running.
Forum: Jet Central Turbines - Artes Jet
02-21-2018, 11:14 AM
Replies: 2
Views: 1,069
Posted By flygono

Just what I wanted to hear. Thank you Jetmon

Just what I wanted to hear.
Thank you Jetmon
Forum: Jet Central Turbines - Artes Jet
02-21-2018, 05:57 AM
Replies: 2
Views: 1,069
Posted By flygono

Airborne re-starts

I have a Jet Central Rabbit SE mounted on a 6m glider. I has about 15-20 flights without issues. I can fly about 12-15 min but usually land at about 8min for safety specially if doing acrobatics...
Forum: RC Jets
01-08-2017, 09:37 AM
Replies: 135
Views: 39,732
Posted By flygono

Thanks for the explanation Peter. The question...

Thanks for the explanation Peter.
The question about the stab incidence is that by sanding the trailing edge of the spacer one would be INCREASING the incidence, not decreasing as stated, it's a...
Forum: RC Jets
01-08-2017, 03:02 AM
Replies: 135
Views: 39,732
Posted By flygono

Can anyone comment on the elevator spacer being...

Can anyone comment on the elevator spacer being sanded down to zero as recommended by CARF, is it absolutely necessary?
Also can some one comment on the 3 servo throws recommended in the manual for...
Forum: RC Warbirds and Warplanes
11-17-2016, 02:24 PM
Replies: 598
Views: 169,295
Posted By flygono

well done Drscoles

well done Drscoles
Forum: RC Warbirds and Warplanes
11-17-2016, 02:13 PM
Replies: 598
Views: 169,295
Posted By flygono

DrScoles Mine is kolm il 135cc. nice repair...

DrScoles
Mine is kolm il 135cc.
nice repair job I did think of doing something similar but without an intact fuse and without a jig there is a chance that i spend months repairing to when flying...
Forum: RC Warbirds and Warplanes
11-17-2016, 01:33 PM
Replies: 598
Views: 169,295
Posted By flygono

Here are some pictures of how I hard installed...

Here are some pictures of how I hard installed the engine only supporting the back.
She proved very strong in the air, so much so that after crashing braking the fuselage and left wing in halve the...
Forum: RC Warbirds and Warplanes
01-04-2016, 07:50 AM
Replies: 598
Views: 169,295
Posted By flygono

Lucky macy what is you email or phone number so...

Lucky macy
what is you email or phone number so we can more privately.
wallingford is 2.5 hours away, are you sure you want to drive this long?
Forum: RC Warbirds and Warplanes
12-29-2015, 02:43 AM
Replies: 598
Views: 169,295
Posted By flygono

Lucky macy engine is mounted with 4 bolts in...

Lucky macy
engine is mounted with 4 bolts in the back, no soft mount.
batteries were mounted as far back as my arm could reach.
I only had to add 4onz into the vertical stab. BB mixed with epoxy....
Forum: RC Warbirds and Warplanes
12-15-2015, 02:56 AM
Replies: 598
Views: 169,295
Posted By flygono

I'm currently flying a comp ARF p-51 with Kolm...

I'm currently flying a comp ARF p-51 with Kolm 135 spinning a falcon 30x13 2 blade prop.
She flies really well and sounds even better.
On ground RPM started at 4900 first couple of flights, now...
Forum: RC Warbirds and Warplanes
10-26-2012, 12:16 PM
Replies: 4,345
Views: 640,034
Posted By flygono

RE: Spitfire Brotherhood (All Spitfires Welcome)

some pictures of my comp arf spit
Forum: RC Warbirds and Warplanes
09-20-2012, 06:55 AM
Replies: 4,345
Views: 640,034
Posted By flygono

RE: Spitfire Brotherhood (All Spitfires Welcome)

Thank's Brad
I will post more pictures in the air in a week or so.
By the way never mind about how to upload pictures. Not difficult to figure out if you pay attention.
Forum: RC Warbirds and Warplanes
09-19-2012, 05:14 PM
Replies: 4,345
Views: 640,034
Posted By flygono

RE: Spitfire Brotherhood (All Spitfires Welcome)

I would like to be a menber of the brotherhood.
I fly a comp ARF spit finished as a Mk IIa.
Fly's beautiful, few mixes to track straight.
can someone tell me how to post pictures in here
Showing results 1 to 16 of 16


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.