RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: craig90
Showing results 1 to 14 of 14
Search took 0.58 seconds.
Forum: RC Jets
07-10-2006, 10:26 AM
Replies: 53
Views: 30,097
Posted By craig90

RE: Fuel station for jet

Does anyone know where I can get this "Wallly World" fuel filter? It looks good, but I cannot find it. Does anyone have any other filter recommendations for a fuel can?

Thanks
02-07-2005, 04:48 PM
Replies: 140
Views: 15,413
Posted By craig90

RE: New H-9 Extra330S

What kind of setup do you guys recommend for a pull pull rudder system? Please post some pics of your rudder setup.
01-30-2005, 09:57 AM
Replies: 35
Views: 5,897
Posted By craig90

RE: Tensor 4D Aerobatics Aircraft

Thinking of purchasing a tensor, what motor is everyone using?
Replies: 7
Views: 901
Posted By craig90

RE: Futaba 9CAP or JR 9X ??

I am using a Futaba 6 channel now with a combintion of hitec and futaba receivers. So you say I cannot use a JR radio with futaba receivers? If not than I think I have already made up my mind.
Replies: 7
Views: 901
Posted By craig90

Futaba 9CAP or JR 9X ??

I am moving up to a new Hangar 9 33% extra and I am looking to purchase a new 9 channel TX from either Futaba or JR. Both JR and Futaba have new 9 channel TXs out. Futaba TX for $400 comes with a...
12-30-2004, 01:19 AM
Replies: 48
Views: 4,308
Posted By craig90

RE: Hanger 9 33% Extra pictures!!¡¡

I was thinking of using a carbon fiber gear. Anyone have any recommendations on what size and where to get one? What servos are everyone using for control surfaces? What servo on the throttle? I...
Forum: ARF or RTF
12-29-2004, 01:06 AM
Replies: 8
Views: 716
Posted By craig90

RE: Segull 300S servo Question

The manual was strange when it came to the elevator servos, but I just went with two 425 BB on the elevators. Set them up on a Y-harness to channel two and they work great. It never hurts to take...
12-18-2004, 10:44 PM
Replies: 140
Views: 15,413
Posted By craig90

RE: New H-9 Extra330S

I am beginnig work on my new H9 Extra, and I will be using a BME 102. Anybody used a pull-pull rudder system yet?
12-18-2004, 10:40 PM
Replies: 44
Views: 2,940
Posted By craig90

RE: COMPOSITE-ARF>>>>>EDGE 540??????

I have just had a couple of minutes on a 2.6m Composite-Arf Yak and it was incredible. I have also flown the 2.6m Extra and it is also an incredible flying machine. Why do you need an edge? Extra...
12-05-2004, 09:19 AM
Replies: 6
Views: 929
Posted By craig90

servo on choke??

I am building an H9 Extra with a BME 102. I was wondering whether or not I should use a separate servo for the choke? I was thinking that I would cut my engine with the Transmitter by simply...
12-01-2004, 10:33 PM
Replies: 7
Views: 649
Posted By craig90

RE: Pull-Pull Rudder on new H9 Extra?

Hooked-On-RC... What made you use a pull-pull system? Do you find any advantages? Do you only use one servo on the rudder?
12-01-2004, 06:54 PM
Replies: 7
Views: 649
Posted By craig90

Pull-Pull Rudder on new H9 Extra?

I just received my new Hangar 9 33% Extra. While going over it I saw that it uses a push-pull rudder. So I was wondering if it was possible to convert the push-pull rudder system into a pull-pull? ...
11-30-2004, 10:02 PM
Replies: 4
Views: 975
Posted By craig90

RE: Hangar 9 Extra 33%

I used to fly at CCRC, but then a couple of months ago I moved to GMA. It is a very nice field with a lot more room.
11-30-2004, 09:02 PM
Replies: 4
Views: 975
Posted By craig90

Hangar 9 Extra 33%

Hey Everyone,
I just received my new ARF Hangar 9 33% Extra, and boy it looks great. I cannot wait to begin building it. I will be using a BME 102, Hitec 5945's on all control surfaces, and a...
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.