RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: jddimck
Showing results 1 to 13 of 13
Search took 0.10 seconds.
02-05-2007, 10:36 PM
Replies: 21,657
Views: 1,507,959
Posted By jddimck

RE: Official HPI MT2 Thread

Thx. On my way to the lhs.
02-04-2007, 10:13 AM
Replies: 21,657
Views: 1,507,959
Posted By jddimck

RE: Official HPI MT2 Thread

Heys guys. What is the best bell gear and spur gear to use to get a great amt of torque. I have had a 2 speed, 49/52, on my MT2 forever, just installed the O.S. .18 CV-R and ready for some bashing....
01-17-2007, 02:09 PM
Replies: 21,657
Views: 1,507,959
Posted By jddimck

RE: Official HPI MT2 Thread

I have used rubberbands in the past on my header and exhaust to hold on the silicon.
01-09-2007, 06:17 PM
Replies: 21,657
Views: 1,507,959
Posted By jddimck

RE: Official HPI MT2 Thread

I'll try that tomorrow, thx
01-09-2007, 06:11 PM
Replies: 21,657
Views: 1,507,959
Posted By jddimck

RE: Official HPI MT2 Thread

no jiggling, high pitch?? Can't figure it out, but seems to run fine. The noise is at the pitch thar drives you CRAZY!
01-09-2007, 06:04 PM
Replies: 21,657
Views: 1,507,959
Posted By jddimck

RE: Official HPI MT2 Thread

ok. Now I have added a shim in fornt of the flw wheel, tightened all real tight w/ thread lock. I seems to be working fine, but it now has a high pitch squeal from the clutch bell, I think. Any...
01-08-2007, 06:52 PM
Replies: 21,657
Views: 1,507,959
Posted By jddimck

RE: Official HPI MT2 Thread

hey guys...need some help again. I can not keep my fly wheel tight on the cone so alls it does is spin. Is it ok to put a shim in front of the fly wheel, behind the nut that holds the fly wheel on...
01-06-2007, 09:31 AM
Replies: 21,657
Views: 1,507,959
Posted By jddimck

RE: Official HPI MT2 Thread

Hey guys. Just got my O.S. .18 CV-R and ready to install. I have a 2 speed on my MT2 and was wondering what was the best gear ratio to get the most torque and keep top speed. Thx in advance for the...
01-03-2007, 04:03 PM
Replies: 21,657
Views: 1,507,959
Posted By jddimck

RE: Official HPI MT2 Thread

thc for the help. On my way to pick it up.
01-03-2007, 09:42 AM
Replies: 21,657
Views: 1,507,959
Posted By jddimck

RE: Official HPI MT2 Thread

Need some help. I am ready to get my O.S. .18 CV-R for my MT2. Is the rotary or slide carb best? What is the big difference? I now have the 18SS on the truck. Thx guys
12-31-2006, 05:30 PM
Replies: 21,657
Views: 1,507,959
Posted By jddimck

RE: Official HPI MT2 Thread

thx. I'll look into that. How is the torque on that engine?
12-31-2006, 05:20 PM
Replies: 21,657
Views: 1,507,959
Posted By jddimck

RE: Official HPI MT2 Thread

Been asking all around the internet on what is the best engine to put in my MT2. I am told the O.S. 18TZ may have to much power and the .18 CV-RX is best. I now have the 18SS and want more. Any other...
12-29-2006, 02:57 PM
Replies: 21,657
Views: 1,507,959
Posted By jddimck

RE: Official HPI MT2 Thread

I am looking for an engine for my HPI MT2. I want a lot of torque as it has a 2 speed and I race short tracks. I now have the 18SS, but want more. Any suggestions? Thx, James
Showing results 1 to 13 of 13


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.