RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: railfly
Showing results 1 to 14 of 14
Search took 0.70 seconds.
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
07-04-2016, 11:07 AM
Replies: 1
Views: 437
Posted By railfly

hited servo compatibility

will the new hsb-9485sh brushless servo work with the jr 921x receiver?
Forum: Gas Engines
07-14-2014, 04:46 AM
Replies: 4
Views: 1,169
Posted By railfly

DLE 30 sheared prop bolts

sheared prop bolts on dle 30 while flying engine sagged and when throttled up sheared prop bolts. Engine had been sagging like running out of fuel on privious flights then died. Took cowl off and...
Forum: ARF or RTF
01-29-2013, 09:21 AM
Replies: 690
Views: 97,720
Posted By railfly

RE: Kangke Waco Biplane

good luck like to hear how the os flies the airplane
Forum: ARF or RTF
12-28-2012, 12:17 PM
Replies: 690
Views: 97,720
Posted By railfly

RE: Kangke Waco Biplane

you will have to cut a hole in the firewall so the carburator can fit behind the firewall so you have the proper clearance for the prop and cowl. I dont think you will for the dle 35. troy models...
Forum: ARF or RTF
12-16-2012, 05:17 PM
Replies: 690
Views: 97,720
Posted By railfly

RE: Kangke Waco Biplane

I sent the measurements from the original to tnt they provide a schematic you can fill in with the measurements. The plane flies great will do all the imac and other maneuvers a little short on power...
Forum: ARF or RTF
12-16-2012, 02:39 PM
Replies: 690
Views: 97,720
Posted By railfly

RE: Kangke Waco Biplane

Have flown mine for about two years with a zdz 40 I was told the DLE 30 is more powerful by a person who works in the tech department at an unnamed dealer. I Think the DLE 35 rear exhaust would be...
Forum: RC Warbirds and Warplanes
11-26-2011, 05:56 AM
Replies: 3,093
Views: 407,737
Posted By railfly

RE: ESM FW D-9

what glue can be used to assemble the cockpit kits?
Forum: RC Warbirds and Warplanes
08-05-2011, 11:52 AM
Replies: 3,093
Views: 407,737
Posted By railfly

RE: ESM FW D-9

one of you who successfully removed the gun hood tell us how also what glue did you use to construct the cockpit kit
Forum: ARF or RTF
06-03-2011, 06:05 PM
Replies: 3
Views: 675
Posted By railfly

RE: hangar 9 sport 40 mustang

took the set screws out of the landing gear and replace with 1/2 inch socket head bolts with the same thread where I could tork them down tight no more wobble.
Forum: ARF or RTF
05-22-2011, 11:59 AM
Replies: 3
Views: 675
Posted By railfly

RE: hangar 9 sport 40 mustang

yes I fly on concrete plane sways from side to side wheels are straight were origanally towed vertically from top to botton straightened to no avail long landing gear too weak to support weight
Forum: ARF or RTF
05-20-2011, 12:42 AM
Replies: 3
Views: 675
Posted By railfly

hangar 9 sport 40 mustang

hangar 9 sport 40 mustang with standard gear waddles like a duck on the runway,anyone have a suggestion on how to fix this.
Forum: Gas Engines
04-02-2010, 06:09 PM
Replies: 662
Views: 85,313
Posted By railfly

RE: DLE30 rear induction conversion!

I still want one theres may not work and apparently yours does allen wentzel
Forum: Gas Engines
03-28-2010, 12:52 PM
Replies: 662
Views: 85,313
Posted By railfly

RE: DLE30 rear induction conversion!

ORIGINAL: railfly

would like one missed the deadline by about 10 days oops not aware of them till then.
Forum: Gas Engines
03-28-2010, 12:47 PM
Replies: 662
Views: 85,313
Posted By railfly

RE: DLE30 rear induction conversion!

would like one missed the deadline by about 10 days oops not aware of them till then.
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.