RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: clockshop
Showing results 1 to 11 of 11
Search took 0.55 seconds.
Forum: ARF or RTF
07-23-2015, 05:47 AM
Replies: 8,173
Views: 874,364
Posted By clockshop

hi I have a revolver and have never had a problem...

hi I have a revolver and have never had a problem with the gear right now aboutt 100 or so flights all on grass runway powered with a saito 100 4 stroke just a great flying and tracking airplane ...
Forum: Electric RC Jets
07-22-2015, 09:14 AM
Replies: 0
Views: 583
Posted By clockshop

j 10

need some help i just purchased a j 10 from a guy every thing is there i just can't get things to work I have the control surfases but not sure if they are right there are wires with only 1 lead a...
Forum: Questions and Answers
09-22-2014, 10:32 AM
Replies: 0
Views: 235
Posted By clockshop

nitro models yak

I have a nitro fiberglass 72 in yak what is the c g measure
Forum: ARF or RTF
08-26-2014, 04:58 AM
Replies: 8,173
Views: 874,364
Posted By clockshop

i have been flying this aircraft for quite awhile...

i have been flying this aircraft for quite awhile i have a sato 100 4 stroke with APC 16x10 just the right set up for this plane it does it all knife edge loops,flat spins,snap rolls, stall turns a...
Forum: RC Warbirds and Warplanes
08-25-2014, 10:29 AM
Replies: 8
Views: 3,460
Posted By clockshop

cut/paste from RCU rules for posts

cut/paste from RCU rules for posts
Forum: Kit Building
06-04-2014, 04:58 PM
Replies: 2,212
Views: 230,938
Posted By clockshop

p47

I have one all done it is powered with a dle 85 using a two blade 2710 tool a little to get use to starting but now runs great what i do is full choke with throdle closed. two flips and it sputters...
Forum: Kit Building
06-04-2014, 04:44 PM
Replies: 2,212
Views: 230,938
Posted By clockshop

hi just finished one all fiberglass and paint...

hi just finished one all fiberglass and paint done to the french p47 don't have any pics yet but will sone this thing is really great pleased with the out come 32 lbs.
Forum: Glow Engines
03-11-2007, 06:11 PM
Replies: 119
Views: 9,688
Posted By clockshop

RE: SuperTigre mid-range problems?

i posted awhile ago that i was having a problem getting the 2300 to richen out at high end and ed i have been using tigers since the early 60ths. this was a problem that i have never had before ...
Forum: Glow Engines
01-07-2007, 10:18 AM
Replies: 119
Views: 9,688
Posted By clockshop

RE: SuperTigre mid-range problems?

hi down under
this is a new set up everything is like it should be i did make the out let tubes smaller it helped some but i still can't get it to run really rich i backed out the idle bar...
Forum: Glow Engines
01-07-2007, 10:06 AM
Replies: 119
Views: 9,688
Posted By clockshop

RE: SuperTigre mid-range problems?

i made some bushing for the tubes and ran the 2300 again today seems a lot better
those having idle problems with the 2300 it takes a little time to get it right but the 2300 will idle really...
Forum: Glow Engines
01-06-2007, 05:25 PM
Replies: 119
Views: 9,688
Posted By clockshop

RE: SuperTigre mid-range problems?

i have read thru this form was hoping to find the problem i have with a st 2300. it is side mounted in a 1/4 yak 54 using a slim line smoke muffler. the engine startes very easy and has great low...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.