RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: 3rdworld
Showing results 1 to 18 of 18
Search took 0.54 seconds.
Forum: Electric Pattern Aircraft
03-15-2012, 06:10 PM
Replies: 1,677
Views: 405,242
Posted By 3rdworld

RE: Extreme Flight Vanquish 2m Build Thread

Thanks all. The kit and the Torque silver bullet have been shipped, also the 21x 14 prop.

Mark
Forum: Electric Pattern Aircraft
03-12-2012, 06:35 PM
Replies: 1,677
Views: 405,242
Posted By 3rdworld

RE: Extreme Flight Vanquish 2m Build Thread

Thanks Guys for all the advise. I have decided to go with the stock Toque Silver bullet motor for now and if i am not happy with that setup, then I will try the Q 60 hacker or possibly the Fury 60/67...
Forum: Electric Pattern Aircraft
03-11-2012, 11:45 AM
Replies: 1,677
Views: 405,242
Posted By 3rdworld

RE: Extreme Flight Vanquish 2m Build Thread

Has anyone tried fitting the Plettenberg Advance 30-10? I know the Hacker Q 60 will just bolt in. Just ordered a Vanquish and looking for a good motor and options available.

Mark
Forum: RC Pattern Flying
11-22-2009, 04:43 PM
Replies: 27
Views: 3,956
Posted By 3rdworld

RE: YS 160 runs too hot in Genesis

Problem solved, here is what was done.
I put another inlet hole in line with the pump.
Added another exit hole in the bottom of the cowl near the front of the pipe.
Switch to a 16 1/2 X 12 prop...
Forum: RC Pattern Flying
11-13-2009, 05:58 PM
Replies: 27
Views: 3,956
Posted By 3rdworld

RE: YS 160 runs too hot in Genesis

It runs just fine with the chin cowl off.

This evening I did another run, this time I used a 17X10N prop and the same 20% fuel. Max RPM 8500 then I open the HS needle to get 8250. Put the cowl...
Forum: RC Pattern Flying
11-12-2009, 06:38 PM
Replies: 27
Views: 3,956
Posted By 3rdworld

RE: YS 160 runs too hot in Genesis

31C is the field temp here in Trinidad. I tried another run this evening (29C) with the cowl side inlet air holes blocked as someone suggested. nil fix
I normally run these YS engines about 1/8...
Forum: RC Pattern Flying
11-11-2009, 06:46 PM
Replies: 27
Views: 3,956
Posted By 3rdworld

RE: YS 160 runs too hot in Genesis

It isn't to lean, there is a lot of smoke actually it's a bit on the rich side and the HS needle responds normal at WOT.
I put an opening in front of the pump with the hope of getting some more air...
Forum: RC Pattern Flying
11-01-2009, 05:32 PM
Replies: 27
Views: 3,956
Posted By 3rdworld

RE: YS 160 runs too hot in Genesis

Thanks Guys,

I did add 4 more holes in the bottom rear of the cowl near the pipe exit(see picture) and there was some improvment but it still gets too hot and shuts down during ground run. I was...
Forum: RC Pattern Flying
11-01-2009, 01:40 PM
Replies: 27
Views: 3,956
Posted By 3rdworld

YS 160 runs too hot in Genesis

I have a YS 160 installed in a Genesis, prop is APC 17 x 12, fuel is 20% Cool Power Heil. With the cowl off the engine runs great 8000 RPM max and idle at 2100 no problem. The engine is new and only...
Forum: RC Pattern Flying
12-06-2006, 09:13 PM
Replies: 78
Views: 8,596
Posted By 3rdworld

RE: Question for Excelleron 90 owners

Can anyone say where I can put my hands on an Excelleron kit as they seem to be out of production?

Mark
Forum: RC Pattern Flying
10-23-2006, 05:35 AM
Replies: 227
Views: 33,056
Posted By 3rdworld

RE: Genesis ARF build, its here.

Thanks Ron,
Did you have to cut the chin cowl to accommodate the gussets on the ES gear?

Mark
Forum: RC Pattern Flying
10-22-2006, 06:27 PM
Replies: 227
Views: 33,056
Posted By 3rdworld

RE: Genesis ARF build, its here.

Grotto2,
What landing gear used on the Genesis in the pictures?

Mark
Forum: RC Pattern Flying
08-16-2006, 09:33 PM
Replies: 15
Views: 2,513
Posted By 3rdworld

RE: Cute Fuel Fittings

Anyone has an update on where I can find these tettra fuel fittings? tried just about every where without success.
Thanks,

Mark
Forum: RC Pattern Flying
10-28-2005, 01:21 PM
Replies: 23
Views: 6,094
Posted By 3rdworld

RE: Mintor 170 Vs OS

Mike,

Many thanks for the information.
So you would go with the OS 140 RX even though the Mintor 170 has more power?
What about the mid range and transition?
Regards,

Mark
Forum: RC Pattern Flying
10-27-2005, 08:48 PM
Replies: 23
Views: 6,094
Posted By 3rdworld

Mintor 170 Vs OS

What's the word out there on the Mintor 170 Vs the OS 140 RX and the FX160
Is the Mintor as reliable as the OS? What about the support and the performance. I have not seen much on...
Forum: RC Pattern Flying
10-15-2005, 08:22 PM
Replies: 259
Views: 55,450
Posted By 3rdworld

RE: X-TREME Composite Astral-XX

Can anyone say who is the US distributor for the Astral XX? And what's the US price?
Forum: RC Pattern Flying
08-17-2005, 06:51 PM
Replies: 2
Views: 971
Posted By 3rdworld

RE: Eclipse 2

The wings are now 73.6 inches not sure what it was before. Could it be that the wing was moved aft a bit?

Mark
Forum: RC Pattern Flying
08-16-2005, 09:28 AM
Replies: 2
Views: 971
Posted By 3rdworld

Eclipse 2

The CA site is now advertising the Eclipse 2. Can any one say what's the differences between the original Eclipse and the Eclipse 2?
Showing results 1 to 18 of 18


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.