RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: flyrccg
Showing results 1 to 14 of 14
Search took 0.10 seconds.
Forum: Giant Scale Aircraft - 3D & Aerobatic
06-22-2006, 05:28 PM
Replies: 1,488
Views: 168,343
Posted By flyrccg

RE: QQ 85" Yak

AMEN Brotha,
Pay attention when gluing your hinges. My ail gaps are clooose. Man, I was proud of a job well done[sm=biggrin.gif], until I checked my throws. 2 5/8"[sm=frown.gif]. It will be plenty...
Forum: Giant Scale Aircraft - 3D & Aerobatic
06-13-2006, 09:06 PM
Replies: 1,488
Views: 168,343
Posted By flyrccg

RE: QQ 85" Yak

Aaron, http://www.aircraftinternational.com sells powerbox systems
Forum: Giant Scale Aircraft - 3D & Aerobatic
06-13-2006, 04:54 PM
Replies: 1,488
Views: 168,343
Posted By flyrccg

RE: QQ 85" Yak

Thanks Angus for the info.

Shakes, I've not finished yet but I checked my throws and found that because I Knotched the hinge points to get smaller gaps I can only get 2.5 inches of throw before...
Forum: Giant Scale Aircraft - 3D & Aerobatic
06-12-2006, 09:09 PM
Replies: 1,488
Views: 168,343
Posted By flyrccg

RE: QQ 85" Yak

Angus
What standoffs did you use with your MVVS 58? I had 1 inch standoffs made for mine and it looks like I'm only going to have 1/4 inch clearence from the cowl. Also how did yours balance?
Forum: Giant Scale Aircraft - 3D & Aerobatic
05-30-2006, 05:23 PM
Replies: 1,488
Views: 168,343
Posted By flyrccg

RE: QQ 85" Yak

Anyone using the MVVS 58. Did you mount your motor directly to the engine box or did you use a stand off? Did it balance ok? I was told byQuiQue to mount it directly to the box but my measurments say...
Forum: Giant Scale Aircraft - 3D & Aerobatic
05-27-2006, 12:27 PM
Replies: 1,488
Views: 168,343
Posted By flyrccg

RE: QQ 85" Yak

Did you put the tri stock on top between the alum. or what? could you post some pics?
Forum: Giant Scale Aircraft - 3D & Aerobatic
05-27-2006, 11:16 AM
Replies: 1,488
Views: 168,343
Posted By flyrccg

RE: QQ 85" Yak

Kent,
What did you or anyone else have to do to the gear plate to improve. Mine has alum. angle, does it need more structure?
Forum: Giant Scale Aircraft - 3D & Aerobatic
05-22-2006, 11:29 AM
Replies: 1,488
Views: 168,343
Posted By flyrccg

RE: QQ 85" Yak

Mike,
From the MVVS 58 manual. As you can see the 22x10 is the smallest prop recommended. PM your email and I'll send you a copy. I'll check back later.

Suggested propeller dimensions:

...
Forum: Giant Scale Aircraft - 3D & Aerobatic
05-22-2006, 11:22 AM
Replies: 1,488
Views: 168,343
Posted By flyrccg

RE: QQ 85" Yak

six
Forum: Giant Scale Aircraft - 3D & Aerobatic
05-22-2006, 11:18 AM
Replies: 1,488
Views: 168,343
Posted By flyrccg

RE: QQ 85" Yak

I have a 3W prop jig. It is the some bolt patern as my 3W 80 and 100.
Forum: Giant Scale Aircraft - 3D & Aerobatic
05-22-2006, 11:01 AM
Replies: 1,488
Views: 168,343
Posted By flyrccg

RE: QQ 85" Yak

Mike,
I have 2 58's, one is going on my QQ to arrive in 2 days, and have been told to prop the moter at 6000-6800 as to not over tach the motor when it unloads in the air. Just be careful. The...
Forum: Giant Scale Aircraft - 3D & Aerobatic
05-21-2006, 01:40 PM
Replies: 1,488
Views: 168,343
Posted By flyrccg

RE: QQ 85" Yak

Thanks guys, I can't wait to get it. I ordered it at the Joe Nall and it should be here mid week.[sm=thumbup.gif] Meanwhile I start reading.
Forum: Giant Scale Aircraft - 3D & Aerobatic
05-21-2006, 10:01 AM
Replies: 1,488
Views: 168,343
Posted By flyrccg

RE: QQ 85" Yak

Thanks Shakes,
I'll see if I can find that thread. Are there any mods that should be done during the build?
Forum: Giant Scale Aircraft - 3D & Aerobatic
05-21-2006, 09:28 AM
Replies: 1,488
Views: 168,343
Posted By flyrccg

RE: QQ 85" Yak

Hello everyone,
I haven't read this entire thread yet so please forgive me for asking. I have a 50cc yak on the way and I'm using a MVVS 58. Has anyone used this motor yet? Has anyone used a...
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.