RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Community
Search
Notices
Search: Posts Made By: clarence_carlsson
Showing results 1 to 11 of 11
Search took 0.52 seconds.
06-11-2013, 12:26 PM
Replies: 5,152
Views: 1,361,357
Posted By clarence_carlsson

RE: MOKI RADIAL Care and Maintenence

No. I used to compete earlier with CompARF Extra 2,6+DA100. The Yak+Moki was built later, but I still fly IMAC patterns. The performance is OK for Sportsman.

/Clarence

<br type="_moz" />
06-11-2013, 12:11 PM
Replies: 5,152
Views: 1,361,357
Posted By clarence_carlsson

RE: MOKI RADIAL Care and Maintenence

Regarding prop sizes:

I have a Krill Models, Yak 55 37% with a Moki 250. I use the Turbulator and a fuel pump. 2% oil.

I have run 2 seasons with a 32x18 but discovered that it revs to high in...
11-26-2011, 12:55 PM
Replies: 5,152
Views: 1,361,357
Posted By clarence_carlsson

RE: MOKI RADIAL Care and Maintenence

Bill: I agree with your ideas about the carburetor. I have discussed this with people who knows engines well, and we beleive the carb is to big. That could make it difficult/impossible to get a...
09-01-2011, 01:51 PM
Replies: 5,152
Views: 1,361,357
Posted By clarence_carlsson

RE: MOKI RADIAL Care and Maintenence

<div>Last flight I noticed a slight change in sound on my Moki 250. I landed at once to inspect. The engine made a different sound while accelerating from idle to midrange. After a while I noticed...
12-03-2009, 05:04 PM
Replies: 5,152
Views: 1,361,357
Posted By clarence_carlsson

RE: MOKI RADIAL Care and Maintenence

Maybe old news to you, but the european distributor of the engine recommends this:

Moki 150:
Zweiblatt (2 blade) 26 x 16; 28 x 14; 30 x 12
Dreiblatt (3 blade) 24 x 16; 26 x14

Moki...
09-29-2009, 09:01 AM
Replies: 5,152
Views: 1,361,357
Posted By clarence_carlsson

RE: MOKI RADIAL Care and Maintenence

I'm sorry if this is off-topic, but you are the guys to ask:

Is it possible to shorten the radial mount on the Moki 150 to get it closer to the firewall? Would it be a problem with heat maybe?
...
08-05-2009, 02:29 PM
Replies: 2
Views: 1,048
Posted By clarence_carlsson

RE: YS 63S - Owners - Final Needle Settings???

Hi,

I have similar settings as you. When I run Coolpower 15%, APC 12x7: the LS needel 1/2 turn, the HS needel 1,5-2,0 turns. The regulator: Well this is a bit strange, I had to turn it in quite...
08-05-2009, 02:22 PM
Replies: 31
Views: 4,583
Posted By clarence_carlsson

RE: YS63 question / problem

I have an FZ63-S with the same symptoms. I am thinking it could be a problem that the engine runs hot, and stops because of this. I have recently changed fuel, and beleive it is a too low oil content...
08-05-2009, 02:19 PM
Replies: 10
Views: 1,971
Posted By clarence_carlsson

RE: Bubbles in carb line

Hi,

I have been struggling with my FZ63-S this week and I have cleaned the regulator (made a big difference), but it still runs bad/erratically and stops after running less than a minute. Can't...
12-09-2006, 05:31 PM
Replies: 2,583
Views: 282,606
Posted By clarence_carlsson

RE: Composite-Arf 2.6 Extra 330

Hi Allan,

You shouldn't have any gap between the spars. Your model seems totally wrong and I think you should contact your dealer to replace the wings. They are not supposed to be like your...
10-24-2006, 02:52 PM
Replies: 2,583
Views: 282,606
Posted By clarence_carlsson

RE: Composite-Arf 2.6 Extra 330

How much aileron difference are you flying with? According to the manual they recommend to use a negative difference of about 10% and that would produce nice rolls. Can someone share their settings...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.