RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: sealth_3
Showing results 1 to 13 of 13
Search took 0.53 seconds.
Forum: Gas Engines
05-15-2018, 11:19 AM
Replies: 4
Views: 1,009
Posted By sealth_3

Thanks.

Thanks.
Forum: Gas Engines
05-15-2018, 06:41 AM
Replies: 4
Views: 1,009
Posted By sealth_3

Thank you for responding. when I installed the...

Thank you for responding. when I installed the new carb, I also replaced the fuel lines too but I will check the tank and exchange it out. Also, what does it mean if there is an air bubble in the...
Forum: Gas Engines
05-14-2018, 01:28 PM
Replies: 4
Views: 1,009
Posted By sealth_3

Carburetor problems on A&M 40cc Engine

I have a 40cc A&M Engine on an Extra 300 airplane and it won’t start. I purchased a carburetor kit and installed it and I still was unable to start it, then I bought a new carburetor and It still...
Forum: RCUniverse.com FAQ
05-02-2015, 06:56 PM
Replies: 0
Views: 502
Posted By sealth_3

Zenoah G-45 Gas Engine Froze

My Zenoah G45 engine was started and run well about three weeks ago. Today I set the chock and flipped the propeller once; then the engine froze. It will only turn half way in each direction and...
Forum: RCUniverse.com FAQ
09-04-2014, 08:23 AM
Replies: 0
Views: 1,117
Posted By sealth_3

Realflight 7 Simulator Setup for Flaperon

I'm unable to setup flaperons for a listed aircraft(Yak54 3D airplane) in Realflight 7(RF7)Simulator. I have a Spektrum DX7s transmitter, and all the setting for flaperons are programed and is...
Forum: Gas Engines
08-07-2014, 01:42 PM
Replies: 4
Views: 2,968
Posted By sealth_3

Thanks for the reply, I was afraid that could be...

Thanks for the reply, I was afraid that could be the problem.
Forum: Gas Engines
08-03-2014, 06:14 AM
Replies: 4
Views: 2,968
Posted By sealth_3

How does one know if engine bearings are bad?

I have a Zenoah G45cc engine I haven't used for a few years. I had problems starting it so I put a new carburetor kit in it, and tried to hand start it to no avail. With the new kit installed, fuel...
Forum: RCUniverse.com FAQ
04-01-2014, 04:46 AM
Replies: 2
Views: 521
Posted By sealth_3

D/R set up for airplanes

I would like to learn how to setup D/R, Expos, and Diff on rc airplanes. Are there any instructions or manuals I can download that will help me ?
Forum: RCUniverse.com FAQ
03-14-2014, 05:33 PM
Replies: 2
Views: 654
Posted By sealth_3

Thanks for the reply. My dx7 died on me and i...

Thanks for the reply. My dx7 died on me and i wanted to replace it with the dx7s transmitter. I have several ar7600 receivers and i feared that they wouldn't be compatible with the dx7s.
Forum: RCUniverse.com FAQ
03-13-2014, 08:06 PM
Replies: 2
Views: 654
Posted By sealth_3

Sepktrum DX73 Compatibility with AR7600 Receiver

Will my AR7600 receivers be compatibility with a DX7s radio?
Forum: ARF or RTF
02-05-2009, 09:44 AM
Replies: 19
Views: 3,045
Posted By sealth_3

RE: H9 NEW F6F HELLCAT PROBLEMS

I just lost a Hangar 9 F6F Hellcat because the firewall was glued to the fuselage with hot glue instead of epoxy. The airplane was flying beautifully until the the firewall separated from the...
Forum: ARF or RTF
02-05-2009, 09:35 AM
Replies: 48
Views: 9,289
Posted By sealth_3

RE: Hanger 9 F6F Hellcat 60

Last weekend, my Hangar 9 F6F Hellcat crashed when the firewall separated from the fuselage. Once the wreckage was recovered, to my surprise, the firewall was hot glued to the fuselage instead of...
Forum: User Product Reviews
04-05-2008, 07:15 PM
Replies: 2
Views: 7,662
Posted By sealth_3

RE: Lanier Giant Stinger Review

Sir,
If you still have your plans for the Lanier Giant Stinger, will you sell them to me? I have a partial built GS and the plans for the wings are unreadable.
Showing results 1 to 13 of 13


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.