RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: w8ye
Showing results 1 to 11 of 11
Search took 0.07 seconds.
Forum: Engine Conversions
05-21-2011, 03:56 AM
Replies: 70
Views: 13,171
Posted By w8ye

RE: Saito 91 on Gasoline

On some engines they may slip a couple times before they settle down and you will have to re-adjust the timing but I never had this problem.

If seen the prop drive washers that were split and...
Forum: Engine Conversions
05-20-2011, 04:42 PM
Replies: 70
Views: 13,171
Posted By w8ye

RE: Saito 91 on Gasoline

I just tighten the prop
Forum: Engine Conversions
05-17-2011, 01:23 PM
Replies: 70
Views: 13,171
Posted By w8ye

RE: Saito 91 on Gasoline

I have a Saito 125 or SG20 with a RCEXL 1/4-32 plug also and it runs fine at idle.
Forum: Engine Conversions
05-16-2011, 04:38 PM
Replies: 70
Views: 13,171
Posted By w8ye

RE: Saito 91 on Gasoline

My Saito 150 idles real well on gas with a RCEXL 1/4-32 plug and the original carb

You may have some other problem like an air leak somewhere?
Forum: Engine Conversions
04-27-2011, 04:52 PM
Replies: 70
Views: 13,171
Posted By w8ye

RE: Saito 91 on Gasoline

Should run fine but there will be a problem with the reach on the CM-6 plug. You will need to shim the plug up with two washers under the threads
Forum: Engine Conversions
04-27-2011, 04:50 PM
Replies: 70
Views: 13,171
Posted By w8ye

RE: Saito 91 on Gasoline

16:1 gas/oil when running the bushed connecting rod

You will need to search for the needle bearing the others are using and select the proper size drill rod for the crank pin to run less oil.
Forum: Engine Conversions
04-15-2011, 06:56 AM
Replies: 70
Views: 13,171
Posted By w8ye

RE: Saito 91 on Gasoline

The Saito 91 doesn't have enough room in it to convert the rod bottom end to needle bearings
Forum: Engine Conversions
03-16-2011, 07:10 PM
Replies: 70
Views: 13,171
Posted By w8ye

RE: Saito 91 on Gasoline

Yes it is the regular Saito 150 glow carby

Our regular pump gasoline is listed as being 89 octane but it is the same as your 92. It is E10. The octane ratings are measured different

I have...
Forum: Engine Conversions
03-16-2011, 05:05 PM
Replies: 70
Views: 13,171
Posted By w8ye

RE: Saito 91 on Gasoline

I just run regular pump gas at 20:1 with Pennzoil aircooled two stroke oil in my Saito 150. It has a CH type conversion using RCEXL ignition and the Saito carb
Forum: Engine Conversions
09-11-2010, 11:23 PM
Replies: 70
Views: 13,171
Posted By w8ye

RE: Saito 91 on Gasoline

Thinks for posting the video.

I noticed your were using the stock carb

Saw the carb was a little sensitive but appeared to be manageable
Forum: Engine Conversions
08-30-2009, 06:57 PM
Replies: 70
Views: 13,171
Posted By w8ye

RE: Saito 91 on Gasoline

The ignition on our model four strokes fires every time the piston comes up

But . . . . Nothing happens on the overlap stroke because there is no compression and the fuel mixture is not correct...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.