RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Search
Today's Posts
Mark Forums Read
Vendor Directory
Notices
Search: Posts Made By: jjoos99
Showing results 1 to 15 of 15
Search took 0.02 seconds.
Forum: Gas Engines
03-14-2018, 06:12 AM
Replies: 2,224
Views: 444,089
Posted By jjoos99

I was flying at a runway behind my home and lost...

I was flying at a runway behind my home and lost the use of the runway so the plane I had bought this engine for has never flown, just test run in the back yard. Hasnt been started since 2016. I...
Forum: Gas Engines
03-13-2018, 08:02 PM
Replies: 2,224
Views: 444,089
Posted By jjoos99

I have an older non pumped version of this...

I have an older non pumped version of this engine. It has been in the plane for several years and only started and ran once. Just wondering if I shouldnt just go ahead and buy the pumped carb and...
Forum: Gas Engines
02-16-2016, 07:34 PM
Replies: 2,224
Views: 444,089
Posted By jjoos99

I bought my engine last winter and was wondering...

I bought my engine last winter and was wondering if horizon is saying when they fixed the crank issue? Or is an issue of repairing the problem as it occurs?
thanks
Jeff
Forum: Gas Engines
01-27-2016, 07:35 AM
Replies: 2,224
Views: 444,089
Posted By jjoos99

so what do you think Al, I have my engine that...

so what do you think Al, I have my engine that has only been run once on the ground. Engine is about 1 1/2 years old. Should I just go ahead and buy the pumped carb and drill the crankcase? I...
Forum: Gas Engines
02-19-2015, 06:20 PM
Replies: 2,224
Views: 444,089
Posted By jjoos99

I believe ahicks just installed the 10gx in the...

I believe ahicks just installed the 10gx in the same plane. Maybe he can chime in on yours.
jeff
Forum: Gas Engines
01-29-2015, 09:14 PM
Replies: 2,224
Views: 444,089
Posted By jjoos99

I picked up a nib funtana 50 this winter and have...

I picked up a nib funtana 50 this winter and have my new 10gx in it. I am anxious to fly it when the winter breaks. I had the funtana before and also loved the way it flew so i wanted another.
jeff
Forum: Gas Engines
01-17-2015, 08:42 PM
Replies: 2,224
Views: 444,089
Posted By jjoos99

Al Lets us know how it maidens out. I had a...

Al
Lets us know how it maidens out. I had a phoenix edge that I put a .72 surpass in. Flew good but if you slowed it down too slow it would tip stall hard. Actually buried it on its second...
Forum: Gas Engines
12-31-2014, 06:15 PM
Replies: 2,224
Views: 444,089
Posted By jjoos99

I just bought my engine less then a month ago and...

I just bought my engine less then a month ago and it came with 2 orange o-rings for each side of the extension. I cut the extension in half and had to put it in the lathe to machine in the stepped...
Forum: Gas Engines
12-31-2014, 01:39 PM
Replies: 2,224
Views: 444,089
Posted By jjoos99

My muffler actually came with two orings, one for...

My muffler actually came with two orings, one for each side of the center section. My center section is made of aluminum. I cut it down to fit my plane. Havent ran the engine yet to tell if it is...
Forum: Gas Engines
12-18-2014, 07:40 PM
Replies: 2,224
Views: 444,089
Posted By jjoos99

Can I install a tee fitting in the main carb line...

Can I install a tee fitting in the main carb line to fuel with? I know with a nitro carb you can flood the engine that way but wont with the walbro carbs it is ok. What is the deal with this carb? ...
Forum: Gas Engines
12-12-2014, 06:04 PM
Replies: 2,224
Views: 444,089
Posted By jjoos99

I cut out the cowl tonight to the muffler in the...

I cut out the cowl tonight to the muffler in the standard position and it wont make any cut difference with the extension. Only thing would be the looks of the muffler sticking down lower. The bad...
Forum: Gas Engines
12-11-2014, 08:03 PM
Replies: 2,224
Views: 444,089
Posted By jjoos99

Al, I got looking at it tonight and I can cut the...

Al, I got looking at it tonight and I can cut the chrome center section in half and turn it down in a lathe and it will still fit good. The extension would work also but I would have to really hack...
Forum: Gas Engines
12-11-2014, 12:28 PM
Replies: 2,224
Views: 444,089
Posted By jjoos99

Hey guys I am mounting up my new evo gx10 and...

Hey guys
I am mounting up my new evo gx10 and was wondering if I can take the chrome center section out of the muffler without effecting performance? I am mounting it sideways in the katana I...
Forum: Gas Engines
11-25-2014, 08:03 AM
Replies: 2,224
Views: 444,089
Posted By jjoos99

I value the opinions on these forums that is why...

I value the opinions on these forums that is why I ask. I am reading the hp ratings of different engines and see that the 10gx is rated higher then the saito .82 yet that motor is on the high side...
Forum: Gas Engines
11-24-2014, 06:50 PM
Replies: 2,224
Views: 444,089
Posted By jjoos99

I am looking at this engine for a hanger 9 50...

I am looking at this engine for a hanger 9 50 katana. I had a .70 surpass on it and it was lacking power for that size of plane. Just wondering how big or heavy of plane others are putting this...
Showing results 1 to 15 of 15


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.