RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Don Szczur
Showing results 1 to 12 of 12
Search took 0.02 seconds.
Forum: Team RCU - Don Szczur
04-25-2020, 08:32 PM
Replies: 14
Views: 7,504
Posted By Don Szczur

Information applies to latest models of Spektrum...

Information applies to latest models of Spektrum transmitters. Will work up a few hints on setting up snap and spin curves on the transmitter if interested. DX 18, IX-12, etc.
Forum: Team RCU - Don Szczur
03-15-2013, 08:38 PM
Replies: 14
Views: 7,504
Posted By Don Szczur

RE: DX18 programming

Section 8-17 of the 10t manual covers Analog switch Setup to allow all sticks and pots to be used as kick point to turn on functions like mixes. The instruction manual is located here: ...
Forum: Team RCU - Don Szczur
02-12-2013, 05:32 PM
Replies: 14
Views: 7,504
Posted By Don Szczur

RE: DX18 programming

Mixing

R-E/A mix- a convenient single screen access point to the knife edge mix features. (rudder to elevator and aileron)

Mix 1 is throttle to elevator for down line mix (to prevent the...
Forum: Team RCU - Don Szczur
02-12-2013, 05:28 PM
Replies: 14
Views: 7,504
Posted By Don Szczur

RE: DX18 programming

- Servo Travel- I try to keep my mechanical adjustments close, and use the travel adjust to only a percent or two for perfect throw alignment of the control surfaces.
Forum: Team RCU - Don Szczur
02-12-2013, 05:25 PM
Replies: 14
Views: 7,504
Posted By Don Szczur

RE: DX18 programming

From the previous post, one other note. The trim setup is at a resolution of 1 for rudder, 1 for aileron, 1 for elevator, and 3 for throttle (I had this much highter for the first flight and...
Forum: Team RCU - Don Szczur
02-12-2013, 05:18 PM
Replies: 14
Views: 7,504
Posted By Don Szczur

RE: DX18 programming

- Trim setup. I have this set up simply right now, with standard trim setup. From the system menu.


- Warnings. I have the throttle warning for 10 percent throttle so I don’t start the...
Forum: Team RCU - Don Szczur
02-12-2013, 05:17 PM
Replies: 14
Views: 7,504
Posted By Don Szczur

RE: DX18 programming

For the Black Magic, setting up dual ailerons and dual elevators
Forum: Team RCU - Don Szczur
02-12-2013, 05:14 PM
Replies: 14
Views: 7,504
Posted By Don Szczur

RE: DX18 programming

Some other helpful setups from my Black Magic powered by a YS 175 engine.

- Aircraft type- this is a simple user graphic that guides you to setting up dual ailerons and dual elevators. This is...
Forum: Team RCU - Don Szczur
02-12-2013, 04:38 PM
Replies: 14
Views: 7,504
Posted By Don Szczur

RE: DX18 programming

With respect to idle down for landing, the same can be done using flight mode trim. I normally land with very low idle (just enough to keep the motor spinning in order to slow the plane down). I...
Forum: Team RCU - Don Szczur
02-12-2013, 04:36 PM
Replies: 14
Views: 7,504
Posted By Don Szczur

RE: DX18 programming

This evening I’ll talk more about flight modes. Here is another example. While flying electric, I noticed that some of the larger pitch propellers that are very light have the tendency to slow...
Forum: Team RCU - Don Szczur
02-11-2013, 06:06 PM
Replies: 14
Views: 7,504
Posted By Don Szczur

RE: DX18 programming

Tonight the first item is related to Flight Modes. I got several questions from folks that are new to Spektrum (or JR for that matter) and are not used to the terminology, “flight mode”. ...
Forum: Team RCU - Don Szczur
02-10-2013, 03:00 PM
Replies: 14
Views: 7,504
Posted By Don Szczur

DX18 programming

I was asked to put together some thoughts and quick hints for setting up a plane on the DX 18. Actually, I was asked to do this for a club program, so here are some notes I'm putting together real...
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.