RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Community
Search
Notices
Search: Posts Made By: mxracerx43
Showing results 1 to 14 of 14
Search took 0.08 seconds.
04-18-2008, 11:34 PM
Replies: 535
Views: 60,258
Posted By mxracerx43

RE: Raptor 50 Titan Discussion

Pretty sure the knurled looking ones go in the hole in the front of the radio tray. Where the Titan kit has the rubber covered standoff with the hitch pins. The others go where the original mounts...
01-07-2008, 01:27 AM
Replies: 535
Views: 60,258
Posted By mxracerx43

RE: Raptor 50 Titan Discussion

You need to join club a with a designated flying feild. See if you can find one with heli pilots. You are going to need help with proper setup and you first flights. I am the only heli guy at my...
01-07-2008, 01:10 AM
Replies: 535
Views: 60,258
Posted By mxracerx43

RE: Raptor 50 Titan Discussion

You can buy a standard JR or Futaba servo (good for throttle) For less than $20.00 new. So why mess with a used (questionable) servo that may cause an expensive, and or dangerous crash? You are...
01-07-2008, 12:47 AM
Replies: 535
Views: 60,258
Posted By mxracerx43

RE: Raptor 50 Titan Discussion

A 50 is a bit easier to fly, they are more stable in a hover less twitchy. They are the same basic size though (30 has a shorter boom) so "veiwing" will be the same.
What brand and # servo are you...
01-07-2008, 12:31 AM
Replies: 535
Views: 60,258
Posted By mxracerx43

RE: Raptor 50 Titan Discussion

You can leave the 4 channel radio and micro servos on the pile, or try to sell them for $$$ for usable helicopter gear. There is always an ongoing debate when it comes to the 30vs50. I had a 30 for...
01-07-2008, 12:12 AM
Replies: 535
Views: 60,258
Posted By mxracerx43

RE: Raptor 50 Titan Discussion

Approx prices for lowend feild gear.
Starter- $29.00
Starter shaft-$15.00
Fuel Pump- $15.00
Fueling plumbing-$15.00
Expanded scale volt meter-$25.00?
Glow starter-$15.00

Yes you need...
12-11-2007, 05:56 PM
Replies: 535
Views: 60,258
Posted By mxracerx43

RE: Raptor 50 Titan Discussion

Hey USMC, that 90 is looking good. How do you like it? I hope this summer I can get into a 90 I am between that or a Trex600N. I like that canopy shceme makes it easy to see. A guy who I was helping...
12-11-2007, 05:49 PM
Replies: 535
Views: 60,258
Posted By mxracerx43

RE: Raptor 50 Titan Discussion

Once you get the controls down a windy da can actually be more fun. Last time I was out it was too windy for any normal flying but the windwas blowing in a constant direction, autos where a blast!...
12-10-2007, 05:35 PM
Replies: 535
Views: 60,258
Posted By mxracerx43

RE: Raptor 50 Titan Discussion

Pic of my 50SE one of the last times I got out. Wish it wasn't so cold.
08-26-2007, 11:23 PM
Replies: 535
Views: 60,258
Posted By mxracerx43

RE: Raptor 50 Titan Discussion

You may want to reconsider the engine and gyro choice. The OS Hyper is a great engine. I only have one experience with a TT engine and it was a 32 in an old V1 I had so I can not personally say to...
06-17-2007, 12:30 PM
Replies: 535
Views: 60,258
Posted By mxracerx43

RE: Raptor 50 Titan Discussion

Yes the receiver will work on 6V. I am not sure what gyro you are using but the popular Futaba 401/9254 combo will not last long using 6 volts. 6volts will also increase you servo tourque and...
06-17-2007, 12:16 PM
Replies: 535
Views: 60,258
Posted By mxracerx43

RE: Raptor 50 Titan Discussion

Hello all I am running a regulated 1950 mah 6 volt pack. I picked it up and the regulator for a lot less than a Duralite setup. I think 6.0 volt is the way to go that way if a cell fails you will not...
06-16-2007, 10:16 PM
Replies: 535
Views: 60,258
Posted By mxracerx43

RE: Raptor 50 Titan Discussion

I just read the last line of your post. I think you are confused, everyone is talking about replacing the original tail rotor hub. You replace it with the one piece unit instead of the stock one...
06-16-2007, 10:13 PM
Replies: 535
Views: 60,258
Posted By mxracerx43

RE: Raptor 50 Titan Discussion

Its not a matter of not bieng able to do 3-d but the fact that the stock part is prone to failure.
I have never personally seen this happen, I am the only guy at my field who flies heli's and...
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.