RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: BB76V
Showing results 1 to 11 of 11
Search took 0.50 seconds.
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
09-25-2008, 11:13 PM
Replies: 6
Views: 3,088
Posted By BB76V

RE: JR DS890G Gyro Servo

I had the same experience. The hobbie store wasn't willing to help out very much at first. I upgraded to the 8900g, I've had good luck since. No more fry out's. Try it out. The gyro and servo work...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
08-14-2008, 08:11 PM
Replies: 6
Views: 3,088
Posted By BB76V

RE: JR DS890G Gyro Servo

i
Forum: Hirobo Support Forum
08-17-2007, 05:03 PM
Replies: 61
Views: 9,747
Posted By BB76V

RE: Welcome Hirobo!

Thanks for the feedback all. I've tried the high speed adjustment that's fine, but I have'nt tried the low end. I will put your suggestions to practical use. Thanks Brandon
Forum: Hirobo Support Forum
08-16-2007, 08:35 PM
Replies: 61
Views: 9,747
Posted By BB76V

RE: Welcome Hirobo!

Well-Idle is about 0 degrees pitch half throttle is 5-7 degrees,and full is 10-12 degrees. Could it be that my clutch is slipping or maybe the engine is becoming weak?
Forum: Hirobo Support Forum
08-14-2007, 08:36 PM
Replies: 61
Views: 9,747
Posted By BB76V

RE: Welcome Hirobo!

I just bought my first gas heli, a hirobo shuttle zxx. It has an o.s .32 on it. The heli will get light on the skids, but won't get air borne. The throttle and the
collective are linked together....
Forum: Glow Engines
05-18-2006, 09:39 AM
Replies: 47
Views: 4,685
Posted By BB76V

RE: Pump setup on OS 160, Did I do it correctly?

I have a the vp30 & the perry pump carb on a st 2300 1.4.MY midrange
is rich. I have the set screw on the pump almost all the way out. I'm
at the the limit.I also noticed fuel being force out of...
Forum: ARF or RTF
05-15-2006, 07:52 PM
Replies: 7
Views: 1,124
Posted By BB76V

RE: Seagull Super Star

sturtz-

The manual states " 7cm from the leading edge". That equals'
2.7559". That doesn't sound right, I agree.You say 4-3/4" worked
fine?If so let me know.I'm putting together a...
Forum: 3D Flying!
04-22-2006, 07:08 PM
Replies: 250
Views: 32,641
Posted By BB76V

RE: New Seagull Edge 540 "68

What was it that you didn't like about the stock carb? Was it the fat mid-range,
the loud up at low idle? These are some of the problems I'm facing.
I have a perry pump installed,and I'm using...
Forum: SuperTigre Engines Support
04-20-2006, 08:30 PM
Replies: 1
Views: 646
Posted By BB76V

st-2300 neddle valve fuel leak

I have a supre tigre 2300- I was retuning the motor and noticed fuel coming out
of the end of the needle valve. Right at the point the needle starts to screw down.
I'm not sure of the technical...
Forum: 3D Flying!
04-16-2006, 10:32 PM
Replies: 2
Views: 872
Posted By BB76V

RE: thunder tiger expo 3-d build and fly report

I TOO BOUGHT AN EXPO. I THINK THE FRAME IS BUILT LIGHT TOO. I RUN A
O.S .46 AX IN IT. WITH A 13X4 APC. PLENTY OF PROP,PLENTY OF POWER. THE
KIT IS WELL PUT TOGETHER,AND COVERED. I THINK IT IS A...
Forum: 3D Flying!
04-10-2006, 08:38 PM
Replies: 250
Views: 32,641
Posted By BB76V

RE: New Seagull Edge 540 "68

Hello- I bought the edge 68". I use a supre tigre gs2300 1.4 c.i. wow what an airplane. vertical all day long. it will do most 3-d maneuver's. the only thing holding it back is me.
the plane was...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.