RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: pe reivers
Showing results 1 to 25 of 500
Search took 0.93 seconds.
06-25-2013, 01:41 AM
Replies: 8
Views: 2,545
Posted By pe reivers

RE: carburetors for a Home Light 25cc

pls correct typo? 28/64 is 7/16"
06-24-2013, 03:47 AM
Replies: 40
Views: 8,168
Posted By pe reivers

Forum: Gas Engines
06-24-2013, 03:46 AM
Replies: 13
Views: 1,174
Posted By pe reivers

RE: Compression issue

+1 on ring gap
06-24-2013, 03:22 AM
Replies: 15
Views: 1,362
Posted By pe reivers

RE: New Be needs help tuning or trouble shooting

Spend a diaphragm/gaskets update kit on the carb. All moving parts must be flabby flexible.
Forum: Glow Engines
06-23-2013, 01:17 PM
Replies: 32
Views: 3,231
Posted By pe reivers

RE: OS 1.20 Go Boom....!!!

Also a possibility.
Forum: Glow Engines
06-23-2013, 12:49 PM
Replies: 32
Views: 3,231
Posted By pe reivers

RE: OS 1.20 Go Boom....!!!

The loose bearing does not look like it suffered. The conrod split because of too high loads.
Just my idea from the pictures. A closer investigation might be needed though. However, it does not look...
Forum: Glow Engines
06-23-2013, 09:38 AM
Replies: 32
Views: 3,231
Posted By pe reivers

RE: OS 1.20 Go Boom....!!!

probable sequence:
Lost prop, over-revved for a few revolutions, and exploded before anyone knew about it.
Nice show.
06-23-2013, 08:08 AM
Replies: 15
Views: 1,362
Posted By pe reivers

RE: New Be needs help tuning or trouble shooting

The fuel never is the problem with these symptoms.
A good walbro writ-up is:
http://www.drystacked.com/Walbro%20Carburetor%20Theory%2027Jun2010.pdf
06-23-2013, 12:55 AM
Replies: 15
Views: 1,362
Posted By pe reivers

RE: New Be needs help tuning or trouble shooting

Clean the carb filter screen.
While at it, check integrity of diaphragms (supple) and gaskets. Replace if needed.
Be careful to fit the pumper diaphragm towards the body before you fit the gasket,...
Forum: Gas Engines
06-21-2013, 03:20 AM
Replies: 47
Views: 3,600
Posted By pe reivers

RE: CM-6 Gas Engine problem

I stock them; made by Rcexl.
Forum: Gas Engines
06-20-2013, 12:42 PM
Replies: 47
Views: 3,600
Posted By pe reivers

RE: CM-6 Gas Engine problem

+1 with Raptureboy.

Rcexl ignitions are known to operate well up to 7V since day one! Maybe with shortened lifespan, but surely not 25 flights. I operate the old types on 2S LiFe battery to be...
Forum: Gas Engines
06-20-2013, 07:16 AM
Replies: 47
Views: 3,600
Posted By pe reivers

RE: CM-6 Gas Engine problem

My guess is that the ignitions are not RCexl at all, but imitations. At least not those from HobbyKing. Xu Liang does not sell to HK.
I see no fault in the setup. Plug gapped to 0.5mm?, Plugs maybe?...
Forum: Gas Engines
06-20-2013, 01:55 AM
Replies: 47
Views: 3,600
Posted By pe reivers

RE: CM-6 Gas Engine problem

What engine? What ignition brand? Were did you buy the ignitions?
Ignition in foam, with tie wraps? Loosely or tight?
This may be important information before we all dumbASSume it is RCexl that is...
Forum: Gas Engines
06-18-2013, 11:31 AM
Replies: 6
Views: 741
Posted By pe reivers

RE: DLE 85 Whats up?

If you read the previous post, it seems there are no users yet!
Forum: Gas Engines
06-18-2013, 11:30 AM
Replies: 2
Views: 557
Posted By pe reivers

RE: 3-Blade on 3W150 Golden Age Racer

The biela would be OK I think.
The 30x12x3 as well, if you pike the blades back to 29" diameter.
Forum: Gas Engines
06-17-2013, 01:26 PM
Forum: Gas Engines
06-17-2013, 01:23 PM
Replies: 3
Views: 561
Posted By pe reivers

RE: Engine Tuning Help!

Try a smaller propeller first. High altitude requires a little more rpm.
Forum: Gas Engines
06-17-2013, 09:45 AM
Replies: 11
Views: 849
Posted By pe reivers

RE: Installing a smoke system.

The good thing is, a smoke every once in a while keeps the muffler insides clean. (no pun intended http://www.rcuniverse.com/forum/js/fckeditor/editor/images/smiley/msn/wink_smile.gif )
06-17-2013, 09:19 AM
Replies: 6
Views: 988
Posted By pe reivers

RE: MVVS wish list

The .15 is in stock.
The .61 can still be ordered.
06-14-2013, 02:11 AM
Replies: 1
Views: 1,018
Posted By pe reivers

RE: MVVS 15 diesel DFSR-RC

I ran the engine at 16300 rpm with a 8x4 MA prop. (using proper fuel of course)
Forum: Gas Engines
06-12-2013, 10:14 AM
Replies: 75
Views: 5,467
Posted By pe reivers

RE: Gas prices

Currently, I pay €1.75 for a quart.
Forum: Gas Engines
06-10-2013, 02:14 PM
Replies: 14
Views: 1,888
Posted By pe reivers

RE: Problem with new DLE55RA

That is a good way to mod the carb. Just forget about the film canister part which only approaches the static tubes, and connect it to real static tubes.
The air pressure inside the fuselage is by...
Forum: Gas Engines
06-08-2013, 02:04 PM
Replies: 14
Views: 1,888
Posted By pe reivers

RE: Problem with new DLE55RA

Fit a carb reference tube to the carb regulator section and connect it to a static device; static tube or static port. Then tune the carb.
Forum: Gas Engines
06-05-2013, 03:29 PM
Replies: 7
Views: 2,407
Posted By pe reivers

RE: Mounting a DLE-35RA

The other hole that lets air in is in the cowling front!!!!??? If not, no larger FW opening would be required, but some fuselage vents would be needed instead.
Forum: Gas Engines
06-04-2013, 02:04 PM
Replies: 7
Views: 2,407
Posted By pe reivers

RE: Mounting a DLE-35RA

Like this? (116cc engine and large carb)
The T-line behind the carb is the static port connection (both sides of the plane) that is attached to the carb regulating section cover.
Yes, there is some...
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.