RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Paolo.75
Showing results 1 to 23 of 23
Search took 0.47 seconds.
Forum: RC Boats General Discussion
07-16-2009, 02:48 PM
Replies: 7,784
Views: 907,633
Posted By Paolo.75

RE: RC Surfer

Probably from the motor shaft...
Forum: RC Boats General Discussion
06-20-2008, 03:23 PM
Replies: 7,784
Views: 907,633
Posted By Paolo.75

RE: RC Surfer

Hi, the ESC is a Pulso DLB-60 Opto that I brought on ebay last year...the battery pack is seven cell, GP 3700 or Grepow 3300.
Forum: RC Boats General Discussion
06-18-2008, 02:51 PM
Replies: 7,784
Views: 907,633
Posted By Paolo.75

RE: RC Surfer

My Kyosho dude also suffers a little problem with alignment, a bit of salt water came in through the motor shaft, I had fill the hull with pieces of sponge.
The better way is change to flex...
Forum: RC Boats General Discussion
02-23-2008, 04:29 AM
Replies: 7,784
Views: 907,633
Posted By Paolo.75

RE: RC Surfer

UMM...too much weight near the tail with the 4AA batteries...better choiche is put a ESC instead the stock servo-microswitch off-full throttle, then move the receiver battery pack in the front.;)
Forum: RC Boats General Discussion
02-18-2008, 02:02 PM
Replies: 7,784
Views: 907,633
Posted By Paolo.75

RE: RC Surfer

If you are intersted I have One male original Kyosho Dude new in box (Kyosho SF4BL) and another one new not original.
Forum: RC Boats General Discussion
02-01-2008, 04:33 PM
Replies: 7,784
Views: 907,633
Posted By Paolo.75

RE: RC Surfer

x tomatse: check those motors, works good witrh RC Surfer and the seller ship worldwide (Feigao 540 12 for speed, 540 8L or 9L for more torque and much runtime):

...
Forum: RC Boats General Discussion
02-01-2008, 01:37 PM
Replies: 7,784
Views: 907,633
Posted By Paolo.75

RE: RC Surfer

No it's no good, it's too small....don't check rpm data only, there is class type also....choose a motor that I mentioned above.
Forum: RC Boats General Discussion
01-30-2008, 04:43 PM
Replies: 7,784
Views: 907,633
Posted By Paolo.75

RE: RC Surfer

Hi Tomaz,

more turns: - speed, + torque; less turns: + speed but - torque (and more battery consumption).

The motors that you've indicated aren't good, the RC Surfer needs a motor between...
Forum: RC Boats General Discussion
01-30-2008, 12:31 PM
Replies: 7,784
Views: 907,633
Posted By Paolo.75

RE: RC Surfer

You can use 27mm to 31mm propeller, size depend to rpm/volt motor also, smaller prop 27 or 28 with a 3500 rpm/volt motor, I use a brushless Jeti Phasor motor 15/3 2500 rpm/volt with a 30mm x 1.4...
Forum: RC Boats General Discussion
01-22-2008, 09:04 AM
Replies: 7,784
Views: 907,633
Posted By Paolo.75

RE: RC Surfer

The New Quida type will get rusty soon...Kyosho only is good without no mods.
Forum: RC Boats General Discussion
12-10-2007, 03:32 AM
Replies: 7,784
Views: 907,633
Posted By Paolo.75

RE: RC Surfer

Hi vagabondsailor,
like I wrote before in the NQD surfer you must replace every internal part, except the motor mount, because get rusty soon or however are poor,
in my website you can see the...
Forum: RC Boats General Discussion
10-29-2007, 11:47 AM
Replies: 7,784
Views: 907,633
Posted By Paolo.75

RE: RC Surfer

Hi Micha,
you can buy this shaft: http://cgi.ebay.co.uk/Model-Boat-Prop-Shaft-6-inch-M4-threaded-for-propellers_W0QQitemZ280156967587QQihZ018QQcategoryZ140971QQrdZ1QQssPageNameZWD1VQQcmdZViewItem
...
Forum: RC Boats General Discussion
10-29-2007, 09:11 AM
Replies: 7,784
Views: 907,633
Posted By Paolo.75

RE: RC Surfer

Hi, between motor and shaft you must use an alu coupler, kupplung in deutch, with mm hole diameter depend of motor size shaft, 5 or 3,17mm. I bought it on www.hydrorcmania.it an rc boat italian shop,...
Forum: RC Boats General Discussion
10-27-2007, 04:47 AM
Replies: 7,784
Views: 907,633
Posted By Paolo.75

RE: RC Surfer

Yes trimegadon you must replace the control board with a receiver, servo and ESC.

In my models a bit of water came always inside, I think through the shaft tube, but I fill innside with many...
Forum: RC Boats General Discussion
10-27-2007, 03:40 AM
Replies: 7,784
Views: 907,633
Posted By Paolo.75

RE: RC Surfer

Trimegadon what do you mean for pc board? Receiver or electronic speed controller? In the NQD servo and "speed controller" are in the same block...you had to replace with a 2 CH FM receiver and a...
Forum: RC Boats General Discussion
10-22-2007, 05:31 PM
Replies: 7,784
Views: 907,633
Posted By Paolo.75

RE: RC Surfer

Graupner GR321 is the transmission (shaft+tube), shaft is 4mm mm and is required a new coupler 4-3,17mm or 4-5mm, depend by the motor's shaft diameter.
http://www.hydrorcmania.it/AsseEco4mm.jpg
...
Forum: RC Boats General Discussion
10-22-2007, 11:54 AM
Replies: 7,784
Views: 907,633
Posted By Paolo.75

RE: RC Surfer

Hi Micha,
your German friends advices are wrong.

I means rpm/volt, I use a brushless Jeti Phasor 15/3, 2500 rpm/volt, 2500rpm x 8,4 volt (7 cells battery) = 21000 rpm and goes well.

...
Forum: RC Boats General Discussion
10-22-2007, 11:02 AM
Replies: 7,784
Views: 907,633
Posted By Paolo.75

RE: RC Surfer

Hi MiFi,
the car motor betwenn 15-21 turns and 2500-3500 rpm are good.

In the NQD surfer the original shaft, the screws and every metal parts will get rusty soon, you must replace those whith...
Forum: RC Boats General Discussion
10-11-2007, 12:30 PM
Replies: 7,784
Views: 907,633
Posted By Paolo.75

RE: RC Surfer

Apart the board, the figure, the rudder (covered in titanium fibre and with new stainless steel shaft) and the motor mount I've changed everything like can you see in the pics!
Forum: RC Boats General Discussion
10-11-2007, 07:54 AM
Replies: 7,784
Views: 907,633
Posted By Paolo.75

RE: RC Surfer

Yes JT you can see the pics of my models figure at this link:

http://digilander.libero.it/squalettino75/surf%20radiocomandato.htm

Fist the Lisa NQD chinese copy with the board covered in...
Forum: RC Boats General Discussion
10-08-2007, 12:10 PM
Replies: 7,784
Views: 907,633
Posted By Paolo.75

RE: RC Surfer

JT the stock screws for the feet maybe could break into serious wipeot...I've reinforced with adesive velcro straps and a inox 3mm screw like below.
...
Forum: RC Boats General Discussion
10-07-2007, 07:39 AM
Replies: 7,784
Views: 907,633
Posted By Paolo.75

RE: RC Surfer

Hi, the NQD it self right well after wipe out, the Lisa remain still in one side on the water but if you give throttle it self right, and so is for the Kyosho.

In the NQD I've changed...
Forum: RC Boats General Discussion
09-11-2007, 08:25 AM
Replies: 7,784
Views: 907,633
Posted By Paolo.75

RE: RC Surfer

Hi, I have both surfers, Kyosho original dude and the fake one Lisa chinese NQD.

The NQD board is strong and heavier than Kyosho, however good build. But the metal parts very very poor! Yuo must...
Showing results 1 to 23 of 23


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.