RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: chevy43
Showing results 1 to 10 of 10
Search took 0.08 seconds.
Forum: "1/2 A" & "1/8 A" airplanes
07-05-2007, 12:39 AM
Replies: 127
Views: 45,794
Posted By chevy43

RE: Q-Tee Build Thread

The wasp is a very light engine at 1.9 oz. It may be heavier than a cox but not by much.... Don't change the wing.
Forum: "1/2 A" & "1/8 A" airplanes
06-28-2007, 01:33 PM
Replies: 127
Views: 45,794
Posted By chevy43

RE: Q-Tee Build Thread

There are acouple of bipe conversion to the Q-Tee's on the other site in the sport flying forum. Or course they are sparkys......
Forum: "1/2 A" & "1/8 A" airplanes
05-11-2007, 09:42 PM
Replies: 127
Views: 45,794
Posted By chevy43

RE: Q-Tee Build Thread

I wish I knew what the load # meant on the calculator. It does show at 7x3 putting out more thrust at 14,200 than a 6x3 at 17,500. It just seems like it runs better on the 7x3 to me. Just thought...
Forum: "1/2 A" & "1/8 A" airplanes
05-11-2007, 06:41 PM
Replies: 127
Views: 45,794
Posted By chevy43

RE: Q-Tee Build Thread

Have you tried the 7x3 MAS or APC? It is a great prop for that engine. I think you will find it will run longer, quieter and pull harder.....
Forum: "1/2 A" & "1/8 A" airplanes
05-10-2007, 09:56 PM
Replies: 127
Views: 45,794
Posted By chevy43

RE: Q-Tee Build Thread

Sometimes it is because of lean and sometimes rich. I have a couple of thease wasps and they like different tank heights and are quite sensitive to the mixture. Play with the tank height. If you...
Forum: "1/2 A" & "1/8 A" airplanes
03-05-2007, 10:27 PM
Replies: 127
Views: 45,794
Posted By chevy43

RE: Q-Tee Build Thread

Won't the fuel tank add to the nose weight? If there are balance problems anyway, I have a PAW .09 with no plane to put it on right now. I think the Q-Tee could be nice with that engine up front.
Forum: "1/2 A" & "1/8 A" airplanes
03-05-2007, 06:52 PM
Replies: 127
Views: 45,794
Posted By chevy43

RE: Q-Tee Build Thread

Could you just make your wing mounts a little longer and slide your wing back?

That looks like a Wasp up front. I have only run mine on the bench. Despite the general advice about using a...
Forum: "1/2 A" & "1/8 A" airplanes
02-26-2007, 08:11 PM
Replies: 127
Views: 45,794
Posted By chevy43

RE: Q-Tee Build Thread

Wow you are going fast! Well it looks like it is too late now but it has been recomended to put the cabanes ( or whatever they are called ) in after covering which makes covering easier. That was...
Forum: "1/2 A" & "1/8 A" airplanes
02-26-2007, 03:38 PM
Replies: 127
Views: 45,794
Posted By chevy43

RE: Q-Tee Build Thread

I wanted rounded wing tips so I took the wing tip block and layed it down but not quite flat to give a little tip diheadral (sp?). I just thought that might look a litte better.... I also used a...
Forum: "1/2 A" & "1/8 A" airplanes
02-26-2007, 02:20 AM
Replies: 127
Views: 45,794
Posted By chevy43

RE: Q-Tee Build Thread

I've got the wing and tail done on mine..... I built my wing flat and set it up for ailerons. I have had the kit since about '77. I guess 30 years is about how long it takes to build:D

I do...
Showing results 1 to 10 of 10


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.