RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Calendar
Search
Today's Posts
Mark Forums Read
Vendor Directory
Notices
Search: Posts Made By: PROPBUSTER1
Showing results 1 to 13 of 13
Search took 0.65 seconds.
Forum: Marketplace
12-04-2020, 03:47 PM
Replies: 1
Views: 770
Posted By PROPBUSTER1

ESM DC-3 retract motor

ESM DC-3 70.5" retract motor/gearbox. The overall length of the motor/gearbox combo. is 42.24 CM. The thread is 6/32.
Forum: JR Radio & Spektrum Radios
03-23-2017, 10:51 AM
Replies: 84
Views: 49,707
Posted By PROPBUSTER1

Ok. What about trying to use a 3 lead hall effect...

Ok. What about trying to use a 3 lead hall effect sensor on a DA 170. Andy, do you have a suggested pinout and do I need a resister on the sensor output? Left pin Power, center pin Ground and Right...
Forum: Twin & Multi Engine RC Aircraft
08-12-2012, 03:13 PM
Replies: 1,020
Views: 167,093
Posted By PROPBUSTER1

RE: Eletronic engine syncronizer **SUPPORT **

Hello Bill,
I have a twin sync version 2.4 which when I used it a 92” P-38 with glow engines and had no issues other than maybe a little hunting to find sync. I am repowering with two 22CC...
Forum: Giant Scale Aircraft - 3D & Aerobatic
04-13-2004, 05:31 PM
Replies: 13
Views: 1,139
Posted By PROPBUSTER1

RE: 21st Century Fabric for Giant Scale ?

[&o]
My experience was with a 72" J-3 Cub. The 21 Century fabric although shrunk had poor tensile strength resulting in a wing that would warp if I applied any aileron while in a tight loop. I...
Forum: Giant Scale Aircraft - 3D & Aerobatic
11-10-2003, 07:57 PM
Replies: 13
Views: 1,059
Posted By PROPBUSTER1

RE: glass and paint on 40% carden edge

I would use .75 Oz. cloth. If you use anything heavier then you have to load on the primer to fill in the weave. And 3 months later you will see that the surface has shrunk slightly, and the weave...
Forum: Giant Scale Aircraft - 3D & Aerobatic
11-09-2003, 07:08 PM
Replies: 13
Views: 1,059
Posted By PROPBUSTER1

RE: glass and paint on 40% carden edge

Having fiberglassed and painted several planes, I my opinion you would be adding way too much weight. I would estimate about 5~6 pounds. Any of these 40% planes (I have a 40% Carden Edge 540)...
Forum: Glow Engines
10-29-2003, 07:36 PM
Replies: 35
Views: 4,782
Posted By PROPBUSTER1

RE: MOKI Engines

Can someone explain why the Moki prices have gone so high Lately?
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
06-26-2002, 07:35 AM
Replies: 13
Views: 1,107
Posted By PROPBUSTER1

I need names of analyzers to track possible interference

We seem to be getting radio hits at our field. Can anyone suggest the make and model of a RF analyzer that will allow us to track hits and confirm that perhaps someone nearby is using a airplane...
Forum: Glow Engines
05-28-2002, 10:02 PM
Replies: 3
Views: 749
Posted By PROPBUSTER1

1.60 prop

I fly the same combination with a 18x6 prop. It will also do ok with an 18x8. You can get a Apc 18x8 but I had to buy a Mejslik(sic) in a 18x6 more thrust less speed with 18x6.
Forum: Tips & Techniques
05-15-2002, 02:20 AM
Replies: 9
Views: 967
Posted By PROPBUSTER1

Ultracoat Plus

I need to learn the significance of the smilies. I didn't mean to affend you. Peace.
Forum: Tips & Techniques
05-13-2002, 11:13 PM
Replies: 9
Views: 967
Posted By PROPBUSTER1

Ultracoat Plus

Thanks Bob, but Pearl white is not what I want. And what makes you think I want to pay a fortune. I just want another source.
Forum: 3D Flying!
05-13-2002, 03:03 AM
Replies: 10
Views: 1,182
Posted By PROPBUSTER1

Hanger 9 CAP 232 120 - Worth Buying?

I have one with a OS 1.60 and it is an awesome combination. 18x6 mejslik prop. You will love it.
Forum: Tips & Techniques
05-13-2002, 12:10 AM
Replies: 9
Views: 967
Posted By PROPBUSTER1

Ultracoat Plus

Horizon no longer sells Ultracoat plus. I believe it is also sold as Orastick in Germany and Profilm in England. I emailed the factory in Germany 2 times for help in purchasing some, but got no...
Showing results 1 to 13 of 13


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.