RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: LONGREDDOG
Showing results 1 to 16 of 16
Search took 0.43 seconds.
Forum: Everything Diesel
01-18-2020, 02:26 PM
Replies: 18
Views: 2,392
Posted By LONGREDDOG

Thank you for your advice. I have installed a...

Thank you for your advice. I have installed a replacement con rod in the PAW .19 and have run it once.it seems ok.

the next time I have the head off, l will try your removal method. Thanks again,...
Forum: Everything Diesel
05-17-2019, 04:52 PM
Replies: 18
Views: 2,392
Posted By LONGREDDOG

Thanks, guess I’ll leave well enough alone! Hope...

Thanks, guess I’ll leave well enough alone! Hope Dr. diesel can match the damaged con rod so I can try and run it soon.

Thank you again for your help, Ed Stout
Forum: Everything Diesel
05-17-2019, 01:53 PM
Replies: 18
Views: 2,392
Posted By LONGREDDOG

PAW .19 TBR FULL of CARBON (was 19TBR clicks when prop is flipped)

Well. I've gotten a lot of good advice here on this thread so far, maybe you can help with something else.
When I took off the piston the crown has a lot of very brunt on carbon. I had to scrub...
Forum: Everything Diesel
05-16-2019, 09:45 AM
Replies: 18
Views: 2,392
Posted By LONGREDDOG

https://cimg0.ibsrv.net/gimg/www.rcuniverse.com-vb...

https://cimg0.ibsrv.net/gimg/www.rcuniverse.com-vbulletin/2000x1504/image_d3697d9b287594ed800b1ba8845b28a51f56b6b0.jpg

Damaged con rod from .19 tbr
Trying to attach pictures, hopefully I can...
Forum: Everything Diesel
05-14-2019, 05:50 AM
Replies: 18
Views: 2,392
Posted By LONGREDDOG

just a quick up-date, called and talked to Dr....

just a quick up-date, called and talked to Dr. Diesel (Eric Clutton). He “talked” me through removing the con rod and l was able to get it out. The small end is damaged almost broken in two. I’m...
Forum: Everything Diesel
04-25-2019, 07:28 AM
Replies: 18
Views: 2,392
Posted By LONGREDDOG

Repair may be needed.

As l wrote before, there is quite a bit of play when I hold the piston stationary and rotate the prop by hand.
The big end of the con rod looks ok, I can't see the small end that's on on the wrist...
Forum: Everything Diesel
04-22-2019, 01:39 AM
Replies: 18
Views: 2,392
Posted By LONGREDDOG

Thank you for your advice,I will remove the rear...

Thank you for your advice,I will remove the rear cover and check it.
Ed
Well, gazimoto I believe you’re correct.
I took off the cover and the “big end” of the rod looks ok,
but I used a soft...
Forum: Everything Diesel
04-18-2019, 05:18 PM
Replies: 18
Views: 2,392
Posted By LONGREDDOG

paw .19 tbr clicks when the prop is fliped

Got a used PAW .19 tbr mark 2 diesel the other day. When you flip the prop over by hand it makes a clicking sound. Is this normal?
I have a PAW .09 and it does not make any noise like that.
Should...
Forum: Gas Engines
06-16-2012, 06:41 PM
Replies: 8
Views: 7,827
Posted By LONGREDDOG

RE: US 41 engine manual

Can anyone tell me what kit number for the walbro carb. is? I have an older engine (US41) that is new, but would like to replace the kit with one that is compatable with gas mixed with ethanol. Read...
Forum: Kit Building
03-29-2010, 12:38 PM
Replies: 4
Views: 2,230
Posted By LONGREDDOG

Precedent T240 kit, need instrutions

Have a Precenent T240 kit that belonged to a modeler that has passed away.
It looks complete with two plans , one of the wings and the other of the tail group. It also has a sheet of pictures...
Forum: Everything Diesel
07-21-2009, 03:46 PM
Replies: 10
Views: 1,885
Posted By LONGREDDOG

RE: Need help with OK Cub diesel

Thank's locktite for your advise on the "O" ring. Will try the AFT treatment first, before trying anything else.
If It won't run I'll just keep it in my collection. I remember back in the early...
Forum: Everything Diesel
07-20-2009, 03:13 PM
Replies: 10
Views: 1,885
Posted By LONGREDDOG

RE: Need help with OK Cub diesel

Mr. cox and gcb, thanks for your help! I've run a two diesels PAW .09, Supertigre .15 (still have them), a LONG while back, so I know a little about them.
The Cub looks like a little differnt...
Forum: Everything Diesel
07-19-2009, 05:10 PM
Replies: 10
Views: 1,885
Posted By LONGREDDOG

Need help with OK Cub diesel

I have a{seems like a nearly new) .075 OK cub diesel and need some help on a few questions.

First,when it's fliped over it seems to have good compresion, but it won't hold it at TDC. After...
Forum: "1/2 A" & "1/8 A" airplanes
04-20-2009, 05:06 PM
Replies: 16
Views: 1,839
Posted By LONGREDDOG

RE: Need help with Sure start engine mount.

Thanks to everyone for the ideas! All the screws have the coarse thead, and both the engine backplate and the mount are not threaded, so it seems that the screws are suposed to go through the...
Forum: "1/2 A" & "1/8 A" airplanes
04-19-2009, 08:08 PM
Replies: 16
Views: 1,839
Posted By LONGREDDOG

RE: Need help with Sure start engine mount.

Thanks for your picture, I'll try it out tomorow. I also don't understand why the extra two screws were in the package.
Once again thanks for the info. Ed.
Forum: "1/2 A" & "1/8 A" airplanes
04-19-2009, 05:36 PM
Replies: 16
Views: 1,839
Posted By LONGREDDOG

Need help with Sure start engine mount.

I purchased the plastic engine mount for a sure start .049, from "Bay". It came with six screws , two of them are about 7/8" long , two are about 5/8" in. and two are about 3/8". I can't figure out...
Showing results 1 to 16 of 16


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.