RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: rmartignoni
Showing results 1 to 11 of 11
Search took 0.09 seconds.
Forum: ARF or RTF
07-06-2008, 08:58 PM
Replies: 4,034
Views: 313,269
Posted By rmartignoni

RE: Hangar 9 Twist 3D Part II - Thread Continuation

What do you think it's the best combination? 55AX or the 61FX? I noticed that 55AX is almost 100g lighter than the FX.... I'm using a Magnum .46 on my .40 t-t and it doesn't have much room to go out...
Forum: ARF or RTF
01-26-2008, 09:57 PM
Replies: 4,034
Views: 313,269
Posted By rmartignoni

RE: Hangar 9 Twist 3D Part II - Thread Continuation

what do you think about a Magnum .52 XLS with a .40 T---T? I'm using a .46 XLS Magnum on it but I don't have much power to go vertical after a torque roll... the .52 weights the same as the .46...
Forum: ARF or RTF
11-11-2007, 07:49 PM
Replies: 4,034
Views: 313,269
Posted By rmartignoni

RE: Hangar 9 Twist 3D Part II - Thread Continuation

hi guys! here are some vids I made today flying my t---t :D

http://www.youtube.com/watch?v=0GGlhp3P8vU

http://www.youtube.com/watch?v=KHAqIH-qlbQ

...
Forum: ARF or RTF
11-08-2007, 09:32 PM
Replies: 4,034
Views: 313,269
Posted By rmartignoni

RE: Hangar 9 Twist 3D Part II - Thread Continuation

so... do you think if i can set all my trims to where all control surfaces are aligned i can do a nice knife edge, even slow?

i'll try this...
Forum: ARF or RTF
11-08-2007, 05:19 PM
Replies: 4,034
Views: 313,269
Posted By rmartignoni

RE: Hangar 9 Twist 3D Part II - Thread Continuation

is it possible to make smoke in a 2 cycle engine?
Forum: ARF or RTF
11-08-2007, 04:15 PM
Replies: 4,034
Views: 313,269
Posted By rmartignoni

RE: Hangar 9 Twist 3D Part II - Thread Continuation

I`m using a Magnum .46 with a 12.25x3.75 APC prop...
Forum: ARF or RTF
11-08-2007, 01:17 PM
Replies: 4,034
Views: 313,269
Posted By rmartignoni

RE: Hangar 9 Twist 3D Part II - Thread Continuation

i think my t---t is with some problem so... when i try a knife edge the plane tend to flip up-side down... always... i have to use pitch (stick down) and a lot of airleron... the plane lose speed...
Forum: ARF or RTF
11-08-2007, 10:09 AM
Replies: 4,034
Views: 313,269
Posted By rmartignoni

RE: Hangar 9 Twist 3D Part II - Thread Continuation

Could someone tell me if it's possible to do a slow knife edge flight with the t---t or even a fast knife edge without using pitch and airleron to keep it in a straight flight?
Forum: ARF or RTF
10-31-2007, 02:19 PM
Replies: 4,034
Views: 313,269
Posted By rmartignoni

RE: Hangar 9 Twist 3D Part II - Thread Continuation

guys... do you think a Magnum XL-91RFS 4-Stroke fits the stock mount of my twist?
Forum: ARF or RTF
10-27-2007, 09:38 AM
Replies: 4,034
Views: 313,269
Posted By rmartignoni

RE: Hangar 9 Twist 3D Part II - Thread Continuation

thanks for the tip guys... next month I`ll buy a new engine but I don`t which one is better OS 55AX or OS 61FX... Sorry about this offtopic reply but certainly you are the right people to answer me...
Forum: ARF or RTF
10-26-2007, 08:06 PM
Replies: 4,034
Views: 313,269
Posted By rmartignoni

RE: Hangar 9 Twist 3D Part II - Thread Continuation

Hi guys! This is my first post here :)

I bought a Twist 40 last month! It`s awesome! Great plane, great flight, easy to control... But now I have a doubt... I`m using a brand new Magnum .46 XLS...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.