RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: drifter
Showing results 1 to 13 of 13
Search took 0.06 seconds.
Forum: Twin & Multi Engine RC Aircraft
12-21-2003, 12:30 PM
Replies: 1,138
Views: 357,969
Posted By drifter

RE: OV-10 <span class=

Does that include the retracts? If not ...
Forum: Twin & Multi Engine RC Aircraft
10-07-2003, 09:05 PM
Replies: 1,138
Views: 357,969
Posted By drifter

RE: OV-10 Bronco 81"

Here is a shot of the first takeoff. Two ST 90's running very rich had no problem hauling the 21lbs into the air. Flaps were used on takeoff because the inadequate 3/16 wire gear flexed and bent so...
Forum: Twin & Multi Engine RC Aircraft
10-07-2003, 08:59 PM
Replies: 1,138
Views: 357,969
Posted By drifter

RE: OV-10 Bronco 81"

Here is a shot of the tail of my Bronco. You can see the servo mounted in the fin. There are servos in both fins. Low profile servos fit well in the fiberglass fins.
Forum: Twin & Multi Engine RC Aircraft
08-05-2003, 02:07 PM
Replies: 1,138
Views: 357,969
Posted By drifter

OV-10 Bronco 81"

Yours weighs two pounds more than mine and has less power. That would scare me. Not saying it won't work, but I have really serious doubts. Any way to swap in more power? :eek:
Forum: Twin & Multi Engine RC Aircraft
06-26-2003, 12:33 PM
Replies: 1,138
Views: 357,969
Posted By drifter

OV-10 Bronco 81"

Nony,
Mine weighs about 19 pounds, and has twin flight packs, plus flaps and retracts. The wing is fully sheeted, and it is painted with latex . 19 pounds is before the 2 pounds of nose weight it...
Forum: Twin & Multi Engine RC Aircraft
06-02-2003, 04:14 PM
Replies: 1,138
Views: 357,969
Posted By drifter

update

Here is the plane shown on page one of this thread. It's in the same position, but a little further along.

This is not the plane shown by nony.
Forum: Twin & Multi Engine RC Aircraft
04-10-2003, 12:28 AM
Replies: 1,138
Views: 357,969
Posted By drifter

Plans

Go here for plans:

http://www.rcstore.com/rs/general/detail.asp?catnum=fsp0201a&catego=PL
Forum: Twin & Multi Engine RC Aircraft
04-09-2003, 05:27 PM
Replies: 1,138
Views: 357,969
Posted By drifter

Elevator control

I've got two Hitec (s-77's I think) low profile servos mounted in the upper fins. I didn't trust the four bellcrank system suggested on the plans. Too much opportunity for slop and binding.

The...
Forum: Twin & Multi Engine RC Aircraft
04-09-2003, 03:30 PM
Replies: 1,138
Views: 357,969
Posted By drifter

progress

Getting ready to glass the wing.
Forum: Twin & Multi Engine RC Aircraft
03-19-2003, 02:30 PM
Replies: 1,138
Views: 357,969
Posted By drifter

bronco wing

The Bronco wing panel is 15" cord by 40.5" span. A 48"x18" board will work. The two wing panels are then joined on something long enough to maintain accurate alignment. The nacelle is about 38"...
Forum: Twin & Multi Engine RC Aircraft
03-18-2003, 06:07 PM
Replies: 1,138
Views: 357,969
Posted By drifter

parts

I purchased them here from this ad:
http://www.rcuniverse.com/showthread.php?s=&threadid=91761&forumid=193&highlight=bronco+combo]
Forum: Twin & Multi Engine RC Aircraft
03-17-2003, 10:43 PM
Replies: 1,138
Views: 357,969
Posted By drifter

retracts

The retracts are heavy duty with a firewall mount nosegear. Simple wire struts. The nose gear strut from Springair was unusable because the coil struck the gear frame preventing complete retraction....
Forum: Twin & Multi Engine RC Aircraft
03-17-2003, 09:36 PM
Replies: 1,138
Views: 357,969
Posted By drifter

fiberglass parts

They are available but I don't know from whom. I bought these from someone here on RCU. The balsa parts are from the Uravitch plan. The glass parts are less boxy and just look better. Going to use...
Showing results 1 to 13 of 13


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.