RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: DerekChurch12
Showing results 1 to 17 of 17
Search took 0.39 seconds.
Forum: Questions and Answers
03-18-2009, 08:58 PM
Replies: 0
Views: 353
Posted By DerekChurch12

120 CMP Cessna Gas to Electric??

I have never converted from gas to electric but I want to do away with my 120 zenoah gas engine and convert it to electric. What steps will be involved? What all will I need and is this even...
Forum: Electric RC Jets
03-17-2009, 09:33 PM
Replies: 2
Views: 633
Posted By DerekChurch12

RE: Art-Tech F-18 TX AND RX question?

Alright very simple then! Thanks a lot!
Forum: Electric RC Jets
03-17-2009, 06:23 PM
Replies: 2
Views: 633
Posted By DerekChurch12

Art-Tech F-18 TX AND RX question?

I have the Art-Tech f-18 with the 2.4 radio on the way. My question is this: Can I put my JR Sport 6 channel transmitter and reciever in place of the reciver and transmitter that comes with the...
Forum: Exceed RC Support - Helicopter
03-17-2009, 01:55 PM
Replies: 7
Views: 1,366
Posted By DerekChurch12

RE: First Rebuild. The Raptor G2 Question.

Awesome! Thanks for the advise!
Forum: Exceed RC Support - Helicopter
03-15-2009, 09:47 PM
Replies: 7
Views: 1,366
Posted By DerekChurch12

RE: First Rebuild. The Raptor G2 Question.

Thanks a lot cjenn. Do I also find 0 pitch for the rotor blades? I know your probably thinking I dont need to be flying 6 channel right now but im trying to learn haha. I looked on map quest for...
Forum: Exceed RC Support - Helicopter
03-15-2009, 12:16 PM
Replies: 7
Views: 1,366
Posted By DerekChurch12

First Rebuild. The Raptor G2 Question.

The Raptor G2 was my first helicopter that wasn't fixed pitch. It is also the first helicopter I am attempting to rebuild. I have to replace the fly bar, main rotors, stabilizers, and the stabilizer...
Forum: Kit Building
03-05-2008, 11:08 PM
Replies: 4
Views: 566
Posted By DerekChurch12

RE: 1.20 Cessna reversing ailerons

Thank you both for your advice. I realize now that I just wasnt paying attention. Since the servos are mirrored in the wing I only need a regular y harness. When I used the reversing y harness this...
Forum: Kit Building
03-04-2008, 11:15 PM
Replies: 4
Views: 566
Posted By DerekChurch12

1.20 Cessna reversing ailerons

I am trying to finish my CMP Cessna 1.20. I cannot figure out how to reverse the ailerons. They move in the same direction. I tried a reversing y-harness but had no luck but I dont even know if I was...
Forum: Kit Building
10-01-2007, 07:48 PM
Replies: 2
Views: 512
Posted By DerekChurch12

New 83" Cessna kit HELP! FLAPS AILERONS

I am in the middle of building the new scale Cessna 83" kit and I am stuck on the ailerons and flaps. I am using a y harness with reverse on both of them. When I try the flaps they want to move in...
Forum: Questions and Answers
09-05-2007, 07:28 AM
Replies: 8
Views: 1,320
Posted By DerekChurch12

RE: How does the Y harness with reverse work

Thanks for all your advise. Thats what I did and I found that I had made a CARELESS mistake in mounting the servo. Thats why they were moving the same direction.
Forum: Questions and Answers
09-04-2007, 01:01 PM
Replies: 8
Views: 1,320
Posted By DerekChurch12

How does the Y harness with reverse work

I am finishing up on my first attempt at building a P-51. The problem is this. My receiver has only one imput for the aileron so I had to use a Y harness with a reverse function. I have messed around...
Forum: Kit Building
09-04-2007, 07:10 AM
Replies: 19
Views: 1,617
Posted By DerekChurch12

RE: New builder, almost done, need advise

Awesome. I work a Lowe's part-time while im still in school so im sure they are bound to have some things come into receiving wrapped in that. Ill check there. Thanks again!
Derek C.
Forum: Kit Building
09-03-2007, 08:18 PM
Replies: 19
Views: 1,617
Posted By DerekChurch12

RE: New builder, almost done, need advise

WMB thanks for that advise as well. I've got a lot of good information from a lot of you. Maybe I can use a little method of each to find what works me. WMB do you mind telling me where you got the...
Forum: Kit Building
09-03-2007, 08:45 AM
Replies: 19
Views: 1,617
Posted By DerekChurch12

RE: New builder, almost done, need advise

Driver its funny how you jump to make up something crazy so that you can show up as the last post who "had something to say." First of all, I dont recall saying anything that reflected on the fact...
Forum: Kit Building
09-02-2007, 10:56 AM
Replies: 19
Views: 1,617
Posted By DerekChurch12

RE: New builder, almost done, need advise

N1EDM, you assumed right. You see I posted this under then new builders forum, not the beginner. Although this is my first plane I have built, it is not the first plane I have flown. My first...
Forum: Kit Building
09-01-2007, 10:06 AM
Replies: 19
Views: 1,617
Posted By DerekChurch12

RE: New builder, almost done, need advise

Thanks for all your advise. Ill wait until the engine comes in and check the CG and then decide from there if I need to just use a foam or actually build a mount. Once again thank you for your...
Forum: Kit Building
08-31-2007, 11:11 PM
Replies: 19
Views: 1,617
Posted By DerekChurch12

New builder, almost done, need advise

I am almost done with my first plane. Its a P-51 63" and I am waiting on the engine to come in for it and it will be complete. My question to anyone that can help me is...
What is the best way to...
Showing results 1 to 17 of 17


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.