RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: scwest
Showing results 1 to 14 of 14
Search took 0.36 seconds.
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
08-23-2012, 03:36 PM
Replies: 5
Views: 1,244
Posted By scwest

RE: JR XG Radio in US Anyone Using Yet??

Thanks for the link, VP. I ordered one today.

scw
Forum: JR Radio & Spektrum Radios
08-05-2012, 02:59 PM
Replies: 484
Views: 52,961
Posted By scwest

RE: Let's talk DX18 here!

I've owned a JR 9303, 9503 and now an 11X. I never had to send one of them back to HH for a product recall as I did my DX6i and DX8. I have an interest in telemetry and am now evaluating the Spektrum...
Forum: JR Radio & Spektrum Radios
06-23-2011, 07:19 PM
Replies: 5
Views: 1,438
Posted By scwest

RE: JR Data Transfer Software

Thanks, Rich!
Forum: JR Radio & Spektrum Radios
06-23-2011, 06:29 PM
Replies: 5
Views: 1,438
Posted By scwest

RE: JR Data Transfer Software

Are you using Windows 7? If so, let me know if you are able to do a successful installation. I'm hoping that JR is now supporting 64-bit operating systems. Thanks.
Forum: Questions and Answers
01-18-2010, 08:20 PM
Replies: 6
Views: 1,239
Posted By scwest

RE: Tribute 36 PNP Spinner

I bought the PNP; stock engine, prop, servos, etc. I don't know the exact weight, however I'm sure it's under 5 pounds. I'm also using the Spektrum AR500 receiver since there isn't a very convenient...
Forum: Questions and Answers
06-07-2008, 07:43 PM
Replies: 6
Views: 1,239
Posted By scwest

RE: Tribute 36 PNP Spinner

The .36 is running great! Hovering is no problem. I had to lean the low end for a smoother transition from idle to full power. It must be because I'm flying at an elevation of 4,200'.

By the...
Forum: Questions and Answers
05-19-2008, 12:55 PM
Replies: 4
Views: 789
Posted By scwest

Epoxy Consistancy

What is the proper consitancy of epoxy? I mixed some 5 minute epoxy from Great Planes and it seemed to be too thick - peanut butter-like. It also "squeezed" out of the bottle rather slowly requiring...
Forum: Questions and Answers
05-19-2008, 11:22 AM
Replies: 4
Views: 643
Posted By scwest

RE: DX7 programming max throws?

When discussing "throw percentages" are you talking about servo travel end points or rate percentages in dual rates? I read somewhere that when programming JR servos to more than 140% servo travel...
Forum: Questions and Answers
03-11-2008, 01:01 PM
Replies: 6
Views: 1,239
Posted By scwest

Tribute 36 PNP Spinner

What kind of spinner will fit the recommended prop (APC 11 x 4) on the Hangar 9 Tribute 36 PNP? The included spinner will NOT fit this prop!

Thanks,

SCW
Forum: O.S. Engines Support
03-01-2008, 11:16 PM
Replies: 6
Views: 1,220
Posted By scwest

RE: O.S. 55 AX HORSE POWER RATING?

I'm planning on running an O.S. 55AX on a SIG Somethin' Extra. Because of low ground clearance issues, can I use an eleven inch prop? If so, what pitch do you recommend?
Forum: Questions and Answers
01-20-2008, 10:30 PM
Replies: 7
Views: 1,646
Posted By scwest

RE: SIG Somethin' Extra Props and Servos

Aluminum or Graph Tech Composite?
Forum: Questions and Answers
01-18-2008, 11:40 PM
Replies: 7
Views: 1,646
Posted By scwest

RE: SIG Somethin' Extra Props and Servos

Thanks for the info! I'll let you know which setup works the best.

SCW
Forum: Questions and Answers
01-18-2008, 04:06 PM
Replies: 7
Views: 1,646
Posted By scwest

SIG Somethin' Extra Props and Servos

I have a SIG Somethin' Extra ARF with an O.S. 55AX. What prop(s) would you recommend for break-in and aerobatics? Also, what servos should I use?

Thanks,

SCW
Forum: Aerodynamics
11-27-2007, 03:55 PM
Replies: 11
Views: 2,202
Posted By scwest

RE: Aileron differential

Sorry, Paul. Quite the opposite is true. Extending flaps or deflecting an aileron downward increases the wing area and camber, thereby increasing lift and decreasing the stall speed. The direct...
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.