RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
 
Page 1 of 20
1
2
3
11
Last »
Search: Posts Made By: slawhammer
Showing results 1 to 25 of 500
Search took 1.07 seconds.
Forum: RC Giant Scale Cars
03-25-2010, 12:37 PM
Replies: 903
Views: 115,135
Posted By slawhammer

RE: New to the 1/5 scale RC world

Goneracing.....there is alot of information in my thread about the firehammer......now you should start your own thread....as my thread is for helping people like your self...
With your own...
Forum: RC Giant Scale Cars
03-15-2010, 07:02 PM
Replies: 903
Views: 115,135
Posted By slawhammer

RE: New to the 1/5 scale RC world

well if you have read most of my tread..you will see I had lots of problems...I should have quit..threw it in the trash...It was junk from the
start..but little did I know....I have spent countless...
Forum: RC Giant Scale Cars
03-15-2010, 02:52 PM
Replies: 903
Views: 115,135
Posted By slawhammer

RE: New to the 1/5 scale RC world

Easy enough to do..just set the gear mesh..make a bracket to fit.....first make a temeplete from thin card board..transfer to say 1/8' alum stock..cut it
install your bracket...you have to make...
Forum: RC Giant Scale Cars
03-14-2010, 06:36 PM
Replies: 903
Views: 115,135
Posted By slawhammer

RE: New to the 1/5 scale RC world

Well I am glad that some people still can get useful information for my thread....That was the intent of the firehammer..as was my first gas Rc truck that was bought for
me....all the troubles and...
Forum: RC Giant Scale Cars
02-23-2010, 04:24 PM
Replies: 4
Views: 641
Posted By slawhammer

RE: Clutch shoe

You can reglue the shoe back on..real pain in the butt..I had that happen as well..just replaced the shoes was all
cheap investment....Check this out if ya have trouble with the...
Forum: RC Giant Scale Cars
02-07-2010, 05:00 PM
Replies: 9
Views: 1,028
Posted By slawhammer

RE: WATCH YOUR BEARINGS...

DC: Dan my man..You need to listen to ole slawhammer here....You spend hundred's of dollars on your Rc Car's for
Quality..Right.....Hey man..buy some good quality bearings..not the 99 cent...
Forum: RC Giant Scale Cars
02-05-2010, 06:59 PM
Replies: 903
Views: 115,135
Posted By slawhammer

RE: New to the 1/5 scale RC world

Lars: Well my friend ..yes my project transformed to some thing wonderful......My project is and had been on hold for some time
now...Not sure if I can get back to it...Due too Health reasons and...
Forum: RC Giant Scale Cars
01-03-2010, 03:43 PM
Replies: 351
Views: 43,964
Posted By slawhammer

RE: DC2/GT5/C5/FG/EVO/ELCON/CAD/BEETLE

DC: the walbro 771 carb has the same internals for fuel flow as the 813..just no pump..
and I thought you did say air bubbles from the tank...That there says a line pin hole...
but the klunker...
Forum: RC Giant Scale Cars
01-03-2010, 01:38 PM
Replies: 351
Views: 43,964
Posted By slawhammer

RE: DC2/GT5/C5/FG/EVO/ELCON/CAD/BEETLE

DC: your tank my be fine ..I have no clue on that...They can get a pin hole in tham..
But your fuel cap is vented....so you may look into a better grommet system for the fuel lines...
I have used...
Forum: RC Giant Scale Cars
01-03-2010, 01:23 PM
Replies: 351
Views: 43,964
Posted By slawhammer

RE: DC2/GT5/C5/FG/EVO/ELCON/CAD/BEETLE

DC: my man don't even both with the old 813 carb you have now..I am sure it is junk...possiable worn internals
worn throttle shaft holes...worn accl ball.. weak spring......Just for get it..Use a...
Forum: RC Giant Scale Cars
01-03-2010, 12:23 PM
Replies: 351
Views: 43,964
Posted By slawhammer

RE: DC2/GT5/C5/FG/EVO/ELCON/CAD/BEETLE

DC: I see your building a engine...Let me ask you this same goes for the cad engine..
are you using paper base cylinder gaskets?..If so the horse crap..you will have a air leak...get copper gaskets...
Forum: RC Giant Scale Cars
01-01-2010, 04:31 PM
Replies: 351
Views: 43,964
Posted By slawhammer

RE: DC2/GT5/C5/FG/EVO/ELCON/CAD/BEETLE

DC: like I mentioned..replace every thing in the fuel system & carb....
As for me I am running the modifed engine with Marine Head ..Dark Soul cooling head...With the RN Victory
Fat...
Forum: RC Giant Scale Cars
01-01-2010, 03:32 PM
Replies: 351
Views: 43,964
Posted By slawhammer

RE: DC2/GT5/C5/FG/EVO/ELCON/CAD/BEETLE

DC: my man..you have missed the concept here....
replace all your fuel system & carb..with new parts....Then you know it will be correct..
hey my friend..I have been thru all is from my past with...
Forum: RC Giant Scale Cars
12-30-2009, 07:07 PM
Replies: 351
Views: 43,964
Posted By slawhammer

RE: DC2/GT5/C5/FG/EVO/ELCON/CAD/BEETLE

DC:...your spinning your wheels here..silacone will not work..the gasoline will dissolve it...aand will leak again..
Your best bet to try is a hot soldering gun with flat tip..to melt and fuse the...
Forum: RC Giant Scale Cars
12-30-2009, 01:16 PM
Replies: 351
Views: 43,964
Posted By slawhammer

RE: DC2/GT5/C5/FG/EVO/ELCON/CAD/BEETLE

DC: as to my build it will be a bit before I can get too that....
Reason is: I had to move out of where I was living..with no place to go..So had to resort to the camper on
my pick up trk....As...
Forum: RC Giant Scale Cars
12-29-2009, 06:23 AM
Replies: 19
Views: 11,549
Posted By slawhammer

RE: 23cc Engine break-in

let it warm up a bit...just drive it..say 15 to 20 minutes..let cool down get cold...check the the cylinder head bolts are tight
run again.......let it rip you should br ok.....oil/gas...
Forum: RC Giant Scale Cars
12-29-2009, 06:16 AM
Replies: 6
Views: 863
Posted By slawhammer

RE: whats it worth?

Well teamchrome...This is a tough call...I have seen a alot of Rc units go as rollers....
a good guess would be....$275+shipping....I know better to recoupe some than having to
part it out on the...
Forum: RC Giant Scale Cars
12-26-2009, 01:48 PM
Replies: 155
Views: 35,192
Posted By slawhammer

RE: Moo's new Nutech NMT

Moo: Looking good my friend...Make it happen...you be the man ..and you love to create..so others will
be happy with a good product.......Glad you like the engine & pipe combo.....for this rc...
Forum: RC Giant Scale Cars
12-26-2009, 01:38 PM
Replies: 351
Views: 43,964
Posted By slawhammer

RE: DC2/GT5/C5/FG/EVO/ELCON/CAD/BEETLE

DC: Mooman is correct on the heli coil kit...To do it right the first time...
But you indicated you did not want the hassle or you think you may have a hard time to do the heli coil your self...
...
Forum: RC Giant Scale Cars
12-24-2009, 09:44 PM
Replies: 155
Views: 35,192
Posted By slawhammer

RE: Moo's new Nutech NMT

MOO:...Now you know what I am talking about....with that engine & victory pipe...
Like I said perfact match....when you get it broken in..It will be a screamer.........
I love that combo ...I my...
Forum: RC Giant Scale Cars
12-24-2009, 07:01 PM
Replies: 351
Views: 43,964
Posted By slawhammer

RE: DC2/GT5/C5/FG/EVO/ELCON/CAD/BEETLE

DC: like I have mentioned..get the stud fixed..Cut that jet pipe too make a header....
new carb(813) your 668 stock will get you by for now...new lines & klunker......
Every 5 gallons fuel I use...
Forum: RC Giant Scale Cars
12-24-2009, 03:34 PM
Replies: 351
Views: 43,964
Posted By slawhammer

RE: DC2/GT5/C5/FG/EVO/ELCON/CAD/BEETLE

Dc:...Things Happen...You got too much on your mind...Your loosing the concept of the rc project....
you need to focus on what your doing......But glad you have figured otu what the problem may...
Forum: RC Giant Scale Cars
12-22-2009, 08:12 AM
Replies: 351
Views: 43,964
Posted By slawhammer

RE: DC2/GT5/C5/FG/EVO/ELCON/CAD/BEETLE

DC: I would cut your jet Pipe..to make a header...Automotive parts house should have heat temp hose...
Example..Heater hose..You want Green in color....like 75mm inside dia...
As To buy a...
Forum: RC Giant Scale Cars
12-21-2009, 08:07 PM
Replies: 351
Views: 43,964
Posted By slawhammer

RE: DC2/GT5/C5/FG/EVO/ELCON/CAD/BEETLE

DC: Fix the stud bolt first...make the header....
use the 668 carb for now..at least you will be able to run it and check out the exhaust & new fuel supply...
alwasy make sure you have a dry air...
Forum: RC Giant Scale Cars
12-21-2009, 07:41 PM
Replies: 351
Views: 43,964
Posted By slawhammer

RE: DC2/GT5/C5/FG/EVO/ELCON/CAD/BEETLE

DC: M6 thats a big bolt or stud...do you have any of those.?Who close is the nut to the pipe?
So your saying the old bolt spins in the cylinder..& does not get tight.......
If thats the case..use...
Showing results 1 to 25 of 500
 
Page 1 of 20
1
2
3
11
Last »


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.