RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: rebuilder
Showing results 1 to 15 of 15
Search took 0.07 seconds.
Forum: Speed - Electric
01-06-2010, 06:27 AM
Replies: 37
Views: 10,454
Posted By rebuilder

RE: 42

Will do, thanks wooley! I bet its cold in St. Claire..............dont miss that.........
Forum: Speed - Electric
01-05-2010, 07:22 PM
Replies: 37
Views: 10,454
Posted By rebuilder

RE: 42

Now there's a ring of ice around the lake...........in the deep south?? Gonna be 6 degrees tomorrow nite...............[:'(]
Forum: Speed - Electric
01-04-2010, 10:57 PM
Replies: 37
Views: 10,454
Posted By rebuilder

RE: 42

I'm makin' it square and sharp again........................;)
Forum: Speed - Electric
01-03-2010, 06:45 PM
Replies: 37
Views: 10,454
Posted By rebuilder

RE: 42

I may grind it down square.........got enough rudder left to lose a couple mm's at the back.
Forum: Speed - Electric
01-02-2010, 11:52 PM
Replies: 37
Views: 10,454
Posted By rebuilder

RE: 42

I have a 45mm plastic on it now............the black one. I think i may try it out first...........if it gets hot in 45 seconds or so i'll throw the octura berylium 42 on. I read of many boat vets...
Forum: Speed - Electric
01-02-2010, 11:25 PM
Replies: 37
Views: 10,454
Posted By rebuilder

RE: 42

Ok...............i think its ready for a maiden! [X(]Using a 45mm plastic prop to start out............i feel it will be "easier" on the system to start out. Found an old rudder bracket and made my...
Forum: Speed - Electric
01-01-2010, 09:51 PM
Replies: 37
Views: 10,454
Posted By rebuilder

RE: 42

More.............
Forum: Speed - Electric
01-01-2010, 04:10 PM
Replies: 37
Views: 10,454
Posted By rebuilder

RE: 42

Its feather light......and i was planning on starting with an x442................??
Forum: Speed - Electric
01-01-2010, 01:52 AM
Replies: 37
Views: 10,454
Posted By rebuilder

RE: 42

Thanks Kwaka! All comments and input are highly valued and appreciated! There was actually a law suit against Exxon by Kellogs for using a similar tiger...............The glossy orange was actually...
Forum: Speed - Electric
01-01-2010, 12:47 AM
Replies: 37
Views: 10,454
Posted By rebuilder

RE: 42

Added some flair to the solid color.............seemed logical. Now what about going with the Exxon theme.........ya know, "put a tiger in your tank" and "Exxon" decals.:eek: Or, just leave it like...
Forum: Speed - Electric
12-31-2009, 01:00 PM
Replies: 37
Views: 10,454
Posted By rebuilder

RE: 42

Yeah, I use the basics for propping.............Ryans chart as well, and it would seem like staying on the conservative side of any prop range works best for me. This should most likely fall into the...
Forum: Speed - Electric
12-31-2009, 11:58 AM
Replies: 37
Views: 10,454
Posted By rebuilder

RE: 42

Brod..............suprisingly the 11XL only pulls about 60-80 amps..................Heres a handy chart for the Feigao's. Thanks for lookin!!:D
Forum: Speed - Electric
12-31-2009, 10:18 AM
Replies: 37
Views: 10,454
Posted By rebuilder

RE: 42

No................its actually ridiculously light..........feather light.........but rigid too.......dont know the exact composite makeup but ive never seen one like this..............Im gonna weigh...
Forum: Speed - Electric
12-31-2009, 09:58 AM
Replies: 37
Views: 10,454
Posted By rebuilder

RE: 42" MRP Fountain build........Here we go!!

I have ordered a Feigao 11XL (1577kv) should be here any day..........and it will have a Turnigy 120a ESC ( they are darn near bulletproof). Surface piercing drive will push it on 6s. Be enough goose...
Forum: Speed - Electric
12-31-2009, 12:15 AM
Replies: 37
Views: 10,454
Posted By rebuilder

42" MRP Fountain build........Here we go!!

Here goes!! Some of you will remember the 42" 80's model MRP Fountain i got off ebay for fairly cheap..............I had asked for opinions on setup and i got help from several...
Showing results 1 to 15 of 15


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.